Sherwood RD-705i User Manual (English)

Questions and Answers:

Z
zmillerSep 5, 2025
Why is there no sound from the surround back speakers on my Sherwood RD-705i Receiver?
- S
  Samuel FitzgeraldSep 5, 2025
  If there is no sound from the surround back speakers on your Sherwood Receiver, the input signal format or the current surround mode may not support the 7.1 surround. Also, check if the surround back channels' power amplifier is assigned to "BIAMP" or "ROOM 2". Ensure that the master volume and surround back level are not too low, and that the surround back speaker setting is not set to "NO".
C
cdavisAug 25, 2025
Why is there no sound coming from my Sherwood RD-705i?
- W
  westdarrenAug 25, 2025
  If there is no sound from your Sherwood Receiver, several factors could be the cause. First, check the speaker wire connections. Then, make sure the master volume isn't too low and that the MUTE button is not activated. Also, verify that you've selected the correct input source and that all connections between components are correct. Ensure the HDMI AUDIO OUT is set to AMP and that all audio settings are properly configured.
P
Patrick MeyersAug 25, 2025
What to do if the Sherwood RD-705i remote control doesn't work?
- K
  Kylie GainesAug 26, 2025
  If the remote control unit for your Sherwood Receiver isn't working, the batteries may be exhausted or not loaded correctly. Try replacing the batteries. Additionally, ensure that there are no obstructions blocking the remote sensor on the receiver.
D
Douglas NguyenAug 27, 2025
How to improve poor FM reception on my Sherwood Receiver?
- A
  amyjacobsAug 27, 2025
  To improve poor FM reception on your Sherwood Receiver, start by ensuring an antenna is connected. Adjust the antenna's position for better reception. If the signals are weak, consider installing an outdoor FM antenna.
S
Sonya JeffersonAug 27, 2025
Why can't my Sherwood RD-705i receive any stations?
- D
  Daniel MolinaAug 27, 2025
  If your Sherwood Receiver cannot receive stations, ensure that an antenna is connected. Then, tune in the desired station frequency. If that doesn't work, try moving the antenna and retuning.
H
Heather LuceroAug 28, 2025
Why Sherwood RD-705i cannot connect to network?
- P
  Patrick HillAug 28, 2025
  If your Sherwood Receiver cannot connect to the network, verify that the network is working properly. If you're using a wireless connection, try shortening the distance from the wireless LAN access point or removing any obstacles that may be interfering with the signal.
H
hjohnsonSep 7, 2025
Why is the picture on my Sherwood RD-705i Receiver noisy or distorted?
- J
  Julie FreemanSep 7, 2025
  If you are experiencing noise or a distorted picture on your Sherwood Receiver, the video format of your monitor TV, DVD player, etc., might be different from PAL. Try changing the video format to PAL.
C
christopher39Sep 4, 2025
Why can't my Sherwood RD-705i Receiver play internet radio broadcasts?
- N
  nwilsonSep 4, 2025
  If your Sherwood Receiver cannot play internet radio broadcasts, check the connection status. Only internet radio programs in MP3 and WMA formats can be played on this unit. Additionally, ensure that the radio station is currently broadcasting.
S
spenceralexandraSep 2, 2025
Why can't my Sherwood Receiver receive preset stations?
- J
  James MooreSep 2, 2025
  If your Sherwood Receiver cannot receive preset stations, it's possible that an incorrect station frequency was memorized. In this case, memorize the correct station frequency. It's also possible that the memorized stations were cleared, so try memorizing the stations again.
K
Katherine StuartSep 3, 2025
Why is there no picture with an HDMI connection on my Sherwood Receiver?
- J
  James MckenzieSep 3, 2025
  If you're not getting a picture with an HDMI connection on your Sherwood Receiver, ensure that the HDMI connection between the unit and the monitor TV is properly made. Also, the connected equipment must support HDCP.

Sherwood RD-705i Specifications

General

Frequency Response	10Hz-100kHz (+1dB, -3dB)
Input Sensitivity	200mV (Line)
Speaker load impedance	8 ohms
Tuning range	AM/FM
Total Harmonic Distortion (THD)	0.05%
Total harmonic distortion	0.05%
Video Connections	HDMI