To Next PageTo Next PageWhat to do if my Sherwood RD-7502 Receiver has no power?
If your Sherwood Receiver isn't powering on, there are a couple of things to check. First, make sure the AC input cord is securely connected. If it is, test the AC wall outlet with a lamp or another appliance to ensure the outlet isn't dead or switched off.
How to fix no sound on Sherwood RD-7502 Receiver?
If you're not getting any sound from your Sherwood Receiver, try these steps: * Check the speaker wire connections. * Adjust the master volume to a higher level. * Ensure the MUTE button is not activated. * Verify that you've selected the correct input source. * Confirm that all connections between components are correct.
Why Sherwood RD-7502 stations cannot be received?
If your Sherwood Receiver isn't picking up any stations, make sure an antenna is connected. Also, try tuning in the desired station frequency. If that doesn't work, reposition the antenna and try tuning again.
Why does my Sherwood RD-7502 Receiver remote control not work?
If your Sherwood Receiver's remote control isn't working, first replace the batteries. If that doesn't solve the issue, make sure nothing is blocking the remote sensor on the receiver.
How to improve poor FM reception on Sherwood Receiver?
To improve poor FM reception on your Sherwood Receiver, ensure an antenna is connected. If one is already connected, try changing its position to find the best reception.
What to do if there is no sound from the surround speakers on Sherwood Receiver?
If you're not hearing sound from the surround speakers on your Sherwood Receiver, check these things: * Make sure a surround mode is selected instead of stereo mode. * Adjust both the master volume and surround level. * Ensure you're using a stereo or surround source, not a monaural one. * Verify that the surround speaker setting isn't set to "N" (None); select the desired setting.
What to do if preset stations cannot be received on Sherwood RD-7502?
If you can't receive preset stations on your Sherwood Receiver, it could be due to an incorrect station frequency being memorized. Try memorizing the correct station frequency. Alternatively, the memorized stations might have been cleared, so try memorizing the stations again.
How to troubleshoot no sound from the center speaker on Sherwood RD-7502?
If you're not getting any sound from the center speaker of your Sherwood Receiver, verify that you've selected the desired surround mode instead of Dolby Virtual Speaker or stereo mode. Also, make sure the center speaker setting isn't set to "N" (None); select the correct setting. Finally, adjust the master volume and center level to ensure they aren't too low.
How to eliminate continuous hissing noise during FM reception on Sherwood RD-7502 Receiver?
If you're experiencing continuous hissing noise during FM reception, especially with stereo broadcasts on your Sherwood Receiver, it could be due to weak signals. Try changing the position of the antenna.
What causes no sound from surround back speakers on Sherwood Receiver?
If you're not getting sound from the surround back speakers on your Sherwood Receiver, it might be because the input signal format or the current surround mode doesn't support 7.1 (or 6.1) surround. Ensure you are using the proper conditions for 7.1 (or 6.1) surround playback. Also, check that the master volume and surround back level are appropriately adjusted. Finally, verify the surround back speaker setting isn't set to "N" (None); select the desired setting.
General| Channels | 5.1 |
|---|---|
| Surround output | Dolby Digital, DTS |
| Tuning range | FM: 87.5 MHz - 108.0 MHz, AM: 530 kHz - 1710 kHz |
| Total Harmonic Distortion (THD) | 0.08% |
| Input Sensitivity | 200mV (line) |
| Signal-to-Noise Ratio | 100 dB |
| Digital inputs | coaxial, optical |
| Video Connections | composite |
| Power Output | 100W per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
| Frequency Response | 10 Hz - 100 kHz |
