How to fix system error on Shimano Steps BT-E6010 Bicycle Accessories?
If you experience a system error with your Shimano Steps Bicycle Accessories, ensure the cable is properly connected and not loose. If the problem persists, it's recommended to contact the place of purchase.
Why is the gear position not displayed on my Shimano Steps BT-E6010?
If the gear position is not displayed on your Shimano Steps Bicycle Accessories, it is only displayed when the electronic gear shifting unit is installed. Check if the electric wire connector is disconnected. If you are not sure, contact the place of purchase.
Why does my Shimano Steps Camera Accessories battery drain so fast?
If the Shimano Steps Camera Accessories battery depletes quickly, it could be that the battery has reached the end of its life. In this case, replace the battery with a new one. Alternatively, the battery's temperature might be outside of its operating range. Ensure you use the battery within its specified operating temperature range.
Why is the LED light off on my Shimano Steps Camera Accessories battery charger?
If the Shimano Steps Camera Accessories battery charger LED does not light up, check the charging plug. Ensure no foreign material is attached to the connection area. Remove and reconnect the charging plug. Also, the LED turns off when the battery is fully charged; this is normal. Remove and reconnect the power plug of the battery charger, and then charge again.
What to do if the LED lights up briefly but my Shimano Steps Camera Accessories doesn't power on?
If you press the satellite power button and the LED lights up briefly but the power doesn't turn on for your Shimano Steps Camera Accessories, the (main) battery level might be too low. Try charging the (main) battery. Also, check that the (main) battery is securely connected.
How to fix Shimano Steps Camera Accessories when it cannot charge?
If your Shimano Steps Camera Accessories cannot charge, first, check the power plug of the battery charger. Remove and reconnect it securely, and then try charging again. Next, verify the charging plug of the battery charger is securely inserted into the battery by removing and reconnecting it. Also, check that the charging adapter and charging plug or charging adapter and battery charging port are securely connected. Finally, inspect the connection terminals of the battery charger, charging adapter, or battery for dirt. Clean them with a waste cloth or cotton bud dampened with ethanol, and then try charging again.
Why doesn't the LED light up on my Shimano Steps Camera Accessories battery?
If the Shimano Steps Camera Accessories battery LED does not light up, it may be because the battery level has been at 0% for a long time, or the battery hasn't been charged after purchase. Charge the battery.
Why are my Shimano Steps Camera Accessories battery and charger getting so hot?
If the Shimano Steps Camera Accessories battery and battery charger become hot, the temperature of the battery and battery charger may exceed the operating temperature. Stop charging, and wait a while before starting to charge again.
What to do if the key does not turn on my Shimano Steps Camera Accessories?
If the key does not turn on your Shimano Steps Camera Accessories, foreign material such as dirt or dust may be stuck in the battery or battery mount. Turn the key while pushing the battery in the installation direction. If the battery is removed, follow the cleaning procedure to clean it.
Why won't my Shimano Steps Camera Accessories cycle computer start?
When charging with the battery installed to a bicycle, you cannot turn the cycle computer ON. Stop charging. The power automatically turns OFF if charging is started while the cycle computer is running.
Guidance on crucial safety aspects, covering potential hazards and precautions for safe operation.
Specific instructions and warnings to prevent accidents and ensure the safe use of the product.
Details on connecting SHIMANO STEPS to PCs and smartphones/tablets for configuration and updates.
Explanation of the different assist modes (HIGH, NORM, ECO, OFF, WALK) and their usage scenarios.
Instructions on how to charge the SHIMANO STEPS battery, including different battery types.
Identifies the cycle computer, assist switch, and drive unit components of the system.
Illustrates various battery types (down-tube, rear carrier, integrated) and their respective mounts.
Identifies the battery charger and the switch unit for system control.
Comprehensive guide to charging the battery, including safety warnings and notes.
Explains the meaning of LED lights on the charger and battery for status indication.
How to check battery levels and guidelines for handling the battery, including storage and usage.
Step-by-step instructions for securely installing and safely removing the battery from the bicycle.
Procedure for attaching and detaching the cycle computer to and from its bracket.
Methods for turning the SHIMANO STEPS system power on and off using the cycle computer or battery.
Fundamental controls and interactions with the SHIMANO STEPS system via cycle computer and switch units.
Detailed explanation of buttons and displays on the SC-E6100, SC-E7000, and EW-EN100 units.
Instructions on how to turn the bicycle lights on and off using the system controls.
Understanding the various icons and data displayed on the cycle computer for system status.
How the EW-EN100 unit indicates the current battery level through its LED lamps.
Steps to select and change between different assist modes using the system controls.
Procedure for changing assist modes using the EW-EN100 unit's button and LED indicators.
How to activate and use the walk assist mode for pushing the bicycle.
Detailed steps for operating the walk assist function, including starting, stopping, and exiting.
How to cycle through different travel data screens on the SC-E6100 cycle computer.
Procedure to reset the traveling distance and related data on the SC-E6100 cycle computer.
How to change the displayed travel data on the SC-E7000 cycle computer.
How to switch between automatic and manual gear shifting modes for electronic systems.
Steps to access the setting menu and navigate options on the SC-E6100 cycle computer.
Procedure to enter the setting menu and select options using the SC-E7000 cycle computer.
How to reset traveling distance or specific setting values through the menu.
Instructions for setting the current time (hour and minute) on the cycle computer.
How to configure the preferred starting gear for the start mode function.
Options for configuring the display backlight, including always on, always off, or manual control.
Adjusting the display brightness level of the SC-E6100 cycle computer.
Configuring the battery-powered light to be always on or always off.
Enabling or disabling beep sounds for system operations and errors.
Toggling the unit of measurement between kilometers and miles for display.
Selecting the desired display language for the cycle computer interface.
Choosing the font color for the display, between black and white options.
Customizing the timing of automatic gear shifts to optimize pedaling effort.
Enabling or disabling the feature that provides recommended shift timings.
Steps to reset the rear derailleur protection function after an impact.
How to close the setting menu and return to the main operating screen.
Procedure for resetting RD protection on the EW-EN100 unit using its button.
Information on adjusting gear shifting, typically requiring dealer consultation.
Overview of automatic data backup for the drive unit and when updates are prompted.
Details on frequency bands, power, and firmware versions for wireless system models.
Interpreting various lighting patterns of battery LEDs to diagnose system errors.
Understanding cycle computer error codes (W###) and EW-EN100 indicators for diagnosis.
Interpreting system error codes (E###) displayed on the cycle computer and applying remedies.
Common problems related to assistance not being provided or short traveling distance, with solutions.
Solutions for battery-related issues like stiffness, quick discharge, and recharging problems.
Diagnosing and resolving issues where bicycle lights do not illuminate.
Addressing problems with the cycle computer display, startup, gear position, and settings.
Resolving issues related to switch operation, noises, and gear shifting adjustments.
General| Battery Type | Lithium-ion |
|---|---|
| Nominal Voltage | 36 V |
| Nominal Capacity | 11.6 Ah |
| Watt-hour Rating | 418 Wh |
| Charging Time | 5 hours |
| Compatibility | Shimano Steps E6000 series |
| Weight | 2.55 kg |
| Operating Temperature | -10°C to 40°C |
| Compatible Charger | Shimano Steps EC-E6000 |
To Next Page
