What does error E043 mean on Shimano Steps DU-E6001 Bicycle Accessories?
If you see error E043 on your Shimano Steps Bicycle Accessories, part of the cycle computer’s firmware may be damaged. Contact the place of purchase or bicycle dealer.
Why is the gear position not displayed on my Shimano Steps DU-E6001 Bicycle Accessories?
If the gear position is not displayed on your Shimano Steps Bicycle Accessories, it is only displayed when the electronic gear shifting unit is installed. Check if the electric wire connector is disconnected. If you are not sure, contact the place of purchase.
How to fix system error on Shimano Steps DU-E6001 Bicycle Accessories?
If you experience a system error with your Shimano Steps Bicycle Accessories, ensure the cable is properly connected and not loose. If the problem persists, it's recommended to contact the place of purchase.
Why is assistance not being provided on my Shimano Steps DU-E6001?
If you're experiencing assistance issues with your Shimano Steps Bicycle Accessories, check these potential causes: * Ensure the battery is sufficiently charged and recharge if needed. * If riding on long slopes in summer or carrying heavy loads, turn off the power temporarily. * Assistance is not provided at speeds of 25 km/h or more, so check your speed. For issues related to incorrect connections or problems with the drive unit, cycle computer, or assist switch, contact the place of purchase.
Why won't the lights turn on my Shimano Steps Bicycle Accessories?
If the front light or the tail light does not illuminate even when the switch is pressed on your Shimano Steps Bicycle Accessories, the E-TUBE PROJECT settings may be wrong. Contact the place of purchase.
Why doesn't the replaced battery work on my Shimano Steps DU-E6001 Bicycle Accessories?
If the replaced battery does not work with your Shimano Steps Bicycle Accessories, the firmware of the drive unit may not be compatible with the battery. Contact the place of purchase to inquire about compatibility.
What does error E021 mean on Shimano Steps DU-E6001?
If you see error E021 on your Shimano Steps Bicycle Accessories, the battery connected to the drive unit conforms with system standards but is not supported. Contact your place of purchase or a local bicycle dealer for assistance.
What does error E022 mean on Shimano Steps DU-E6001 Bicycle Accessories?
If you see error E022 on your Shimano Steps Bicycle Accessories, the battery connected to the drive unit does not conform with system standards. Contact your place of purchase or a local bicycle dealer for assistance.
What to do if Shimano Steps DU-E6001 shows temperature protection warning?
To address a temperature protection issue with your Shimano Steps Bicycle Accessories battery, leave the battery in a cool place away from direct sunlight until its internal temperature decreases sufficiently. If the problem continues, contact the place of purchase.
What does W030 error mean on Shimano Steps Bicycle Accessories?
If you encounter error W030 on your Shimano Steps Bicycle Accessories, it could be due to two or more assist switches connected to the system or a communication error between the drive unit and the motor unit. To resolve this: * Change the assist switch to the gear shifting switch, or connect only one assist switch and turn on the power again. * Check that the cable is properly connected between the drive unit and the motor unit. If the situation does not improve, contact the place of purchase.
General| Brand | Shimano Steps |
|---|---|
| Model | DU-E6001 |
| Category | Bicycle Accessories |
| Language | English |
Safety instructions and warnings related to battery handling.
General safety advice to avoid burns or injuries from leaks, heat, fire.
Advice for safe riding, including attention to display and wheel installation.
Precautions for safe product use, including wiring and handling hot components.
Detailed safety instructions for battery handling and temperature limits.
Guidance on cleaning the chain with appropriate agents.
Safe usage advice, including caps, installation, waterproofing, and charging.
Advice on carrying the bicycle in a car and checking battery connectors.
Information on battery disposal regulations within the EU.
Details on cleaning battery and plastic covers, and chain maintenance.
Information on proper assist force and compatibility with brakes.
Note about information on the battery charger label.
Device compliance with FCC rules regarding interference.
Highlights of SHIMANO STEPS, including design, performance, and modes.
Step-by-step guide on how to turn on the power and start riding.
Explanation of different assist modes (HIGH, NORMAL, ECO, OFF, WALK) and their usage.
Initial setup and charging instructions for the battery before first use.
Detailed DANGER and CAUTION notices for battery charging procedures.
Steps for charging the battery while it is mounted on the bicycle.
Explanation of the LED lamp status on the charger and its meaning.
Explanation of the LED lamp status on the battery and charging indicators.
How to check the current battery level via the cycle computer.
Guidelines for charging the battery at specific times and long-term storage.
Step-by-step guide for installing the battery onto the bicycle.
Instructions on how to remove the battery using the key.
How to use buttons on the assist and shifting switches for operations.
Steps for attaching and detaching the cycle computer from its bracket.
How to turn the system power on and off via cycle computer or battery.
Information about the logo screen displayed during system startup and shutdown.
Explanation of various elements displayed on the cycle computer screen.
Visual representation of battery levels on the cycle computer.
How to select different assist modes using the switches.
Steps to activate the walk assist mode for pushing the bike.
How to use and stop the walk assist function.
How to view gear ratio or traveling data on the cycle computer.
How to control the battery-powered light using the cycle computer.
How to switch between automatic and manual gear shifting modes.
Procedure to clear traveling distance data (DST) on the main screen.
How to access the system's settings menu.
Procedure to clear traveling distance or reset display settings to default.
Steps for configuring the clock setting (hour and minute).
How to set the starting gear for the start mode function.
How to configure the display backlight setting (ON, OFF, MANUAL).
How to adjust the backlight brightness to one of 5 levels.
How to turn the beep sound on or off.
How to switch between kilometer and mile distance units.
How to configure the display language setting.
How to change the font color of the display.
How to adjust electronic gear shifting for derailleur settings.
How to adjust shift timing in automatic shift mode.
How to close the settings menu and return to the basic screen.
Information on automatic backup and operations causing backup prompts.
Instructions for downloading and installing the E-TUBE PROJECT software.
Table of battery LED error codes, conditions, and recovery steps.
General warnings and specific codes (W031, W010, W011, W012) with remedies.
Procedures for resetting error displays (E010, E012, E013) and their remedies.
Detailed list of error codes, preconditions, restrictions, and remedies.
Troubleshooting for issues like no assistance, stiff pedaling, and short travel distance.
Troubleshooting for battery issues like rapid discharge, charging problems, and overheating.
Troubleshooting for charger warmth, LED issues, and battery removal/insertion problems.
Troubleshooting for front/tail lights not illuminating.
Troubleshooting for cycle computer display, startup, gear position, beep, backlight, and settings menu.
Other issues like switch operation, beeps, assistance weakening, noises, and start mode shifting.
To Next Page
