Shimano Steps SC-E7000 User Manual

69 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

UM-79H0A-000-00

User's manual

Original instructions

E5000 Series

Shimano Total Electric Power System

Table of Contents

Other manuals for Shimano Steps SC-E7000

User Manual72 pages

Dealer's Manual60 pages

Questions and Answers:

S
Steven PetersAug 17, 2025
What to do if the cycle computer is not displayed when I push the battery power button on my Shimano Steps SC-E7000?
- A
  Anna HoodAug 18, 2025
  If the cycle computer is not displayed when you push the battery power button on your Shimano Steps Bicycle Accessories, try these steps: recharge the battery, and then turn the power on once more. Also ensure that power is turned on (hold down the power button). Stop charging if the battery is charging. Check if the cycle computer is correctly installed to the bracket. Check to see if the connector of the electric wire connecting the motor unit to drive unit is not disconnected.
S
Stanley RandolphAug 20, 2025
Why is assistance not being provided on my Shimano Steps SC-E7000 Bicycle Accessories?
- P
  Peter CookAug 20, 2025
  If assistance isn't being provided by your Shimano Steps Bicycle Accessories, first, verify the battery charge and recharge if low. If riding on long slopes in summer or carrying heavy loads, overheating may occur; turn off the power and wait before trying again. Also, ensure you are pedaling, as the bicycle isn't a motorbike. Assistance is not provided at speeds of 25 km/h or more. Finally, check that the assist mode isn't set to OFF.
J
jacksonkristinAug 22, 2025
What to do if the battery cannot be recharged on Shimano Steps SC-E7000?
- M
  Mandy PattersonAug 22, 2025
  If the battery on your Shimano Steps Bicycle Accessories cannot be recharged, ensure the charger's power plug is securely inserted into the electrical outlet and the recharging plug is securely connected to the battery. Also, check if the charging adapter is properly connected to the charging plug or the battery charging port. Clean the connection terminals with a dry cloth to remove any dirt.
C
Cheryl FuentesAug 26, 2025
Why is the assist traveling distance too short on my Shimano Steps Bicycle Accessories?
- M
  mark80Aug 26, 2025
  If the assist traveling distance is too short on your Shimano Steps Bicycle Accessories, check the battery charge and recharge if necessary. Remember that traveling distance can be affected by road conditions, gear position, and lights being on. Battery performance also decreases in winter weather. If the battery's performance has deteriorated significantly due to repeated charging or long use, consider replacing it.
P
pmckinneyAug 27, 2025
What to do if the LED on the charger does not illuminate for Shimano Steps SC-E7000?
- H
  Harry DiazAug 28, 2025
  If the LED on the charger for your Shimano Steps Bicycle Accessories does not illuminate, check the connection for any foreign objects before reinserting the charging connector. If the battery is fully charged, the LED on the battery charger turns off, but this is not a malfunction. Disconnect and then reconnect the power plug of the charger, and then repeat the recharging operation.
M
Mr. Mark HernandezAug 30, 2025
What to do if the system does not start up when I press the cycle computer power button on my Shimano Steps SC-E7000 Bicycle Accessories?
- C
  Chelsea StanleyAug 30, 2025
  If the system does not start up when you press the cycle computer power button on your Shimano Steps Bicycle Accessories, and you have used the cycle computer in low temperatures for an extended period, turn it on by pressing the power button on the battery. Also, ensure the cycle computer is correctly installed to the bracket.
A
Ashley SchmidtSep 1, 2025
Why is the charger warm for my Shimano Steps Bicycle Accessories?
- J
  Jason MullinsSep 1, 2025
  If the charger for your Shimano Steps Bicycle Accessories is warm, it may be due to continuous use. Allow it to cool down before using it again.
D
Dylan DonaldsonSep 4, 2025
Why do all the five battery level indicators stay on for Shimano Steps SC-E7000 Bicycle Accessories?
- K
  Kenneth ThomasSep 4, 2025
  If all five battery level indicators stay on for your Shimano Steps Bicycle Accessories, the firmware version of the drive unit may be out-of-date. Consult your place of purchase and check the firmware version.
R
Robert FoxSep 6, 2025
Why can a noise be heard from the rear wheel during normal riding on Shimano Steps SC-E7000?
- C
  Christina NicholsSep 7, 2025
  If a noise can be heard from the rear wheel during normal riding with your Shimano Steps Bicycle Accessories, it may be that gear shifting adjustment has not been carried out correctly. For mechanical gear shifting adjust the cable tension.
D
Debbie OrtizSep 9, 2025
Why doesn't the replaced battery work on my Shimano Steps Bicycle Accessories?
- T
  Terry ThomasSep 9, 2025
  If the replaced battery does not work with your Shimano Steps Bicycle Accessories, the firmware of the drive unit may not be compatible with the battery. Contact your place of purchase to inquire about compatibility.

Shimano Steps SC-E7000 Specifications

General

Brand	Shimano Steps
Model	SC-E7000
Category	Bicycle Accessories
Language	English

Summary

Safety and Notices

Safety Information and Handling

Crucial safety advice for using the system and handling the battery.

Safety Warnings

Safe Riding and Product Use

Guidelines for safe riding practices and proper product usage.

Cautions and Precautions

Riding Safety and Product Handling

Cautions for safe riding and product handling, including battery safety.

System Connectivity

PC and Mobile Connection

Connect to PCs and mobile devices via E-TUBE PROJECT for configuration and updates.

Key System Features

Assist Mode Overview

Detailed explanation and visual guide for various SHIMANO STEPS assist modes.

Initial Setup: Battery Charging

Battery Charging Procedures

Initial Setup: Power Management

Initial Setup: Assist Mode Selection

Selecting Assist Mode

Battery Preparation: Charging

Battery Preparation: Installation

System Operation: Power Management

Turning the System Power On/Off

Procedures for turning the SHIMANO STEPS system power ON and OFF.

System Operation: Controls and Displays

Assist Mode Settings

Changing Assist Modes

Walk Assist Mode Operation

Walk Assist Mode

Setting Menu: Access and Navigation

Launching and Navigating the Menu

System Connectivity and Specs

Errors and Troubleshooting

Battery LED Error Indications

Interpretation of battery LED lamp patterns to identify system errors and potential remedies.

Errors and Troubleshooting

Troubleshooting Common Issues

Solutions for common symptoms related to assistance, pedaling stiffness, and battery performance.

Related product manuals

Shimano Steps SC-E6000

Shimano Steps EW-SW100

Shimano Steps EW-SW300

Preview: Shimano Steps E5003

Shimano Steps E5003

Shimano Steps BT-E6010

Shimano Steps DU-E6002

Shimano Steps DU-E6012

Preview: Shimano Steps BT-E6000

Shimano Steps BT-E6000

Shimano Steps EC-E6002

Shimano Steps DU-E6001

Shimano Steps BT-E8035

Preview: Shimano Steps E8000 Series

Shimano Steps E8000 Series