What does error E043 mean on Shimano Steps SC-E6010 Bicycle Accessories?
If you see error E043 on your Shimano Steps Bicycle Accessories, part of the cycle computer’s firmware may be damaged. Contact the place of purchase or bicycle dealer.
Why is the gear position not displayed on my Shimano Steps Bicycle Accessories?
If the gear position is not displayed on your Shimano Steps Bicycle Accessories, it is only displayed when the electronic gear shifting unit is installed. Check if the electric wire connector is disconnected. If you are not sure, contact the place of purchase.
How to fix system error on Shimano Steps SC-E6010 Bicycle Accessories?
If you experience a system error with your Shimano Steps Bicycle Accessories, ensure the cable is properly connected and not loose. If the problem persists, it's recommended to contact the place of purchase.
Why is assistance not being provided on my Shimano Steps SC-E6010?
If you're experiencing assistance issues with your Shimano Steps Bicycle Accessories, check these potential causes: * Ensure the battery is sufficiently charged and recharge if needed. * If riding on long slopes in summer or carrying heavy loads, turn off the power temporarily. * Assistance is not provided at speeds of 25 km/h or more, so check your speed. For issues related to incorrect connections or problems with the drive unit, cycle computer, or assist switch, contact the place of purchase.
Why won't the lights turn on my Shimano Steps Bicycle Accessories?
If the front light or the tail light does not illuminate even when the switch is pressed on your Shimano Steps Bicycle Accessories, the E-TUBE PROJECT settings may be wrong. Contact the place of purchase.
Why doesn't the replaced battery work on my Shimano Steps SC-E6010?
If the replaced battery does not work with your Shimano Steps Bicycle Accessories, the firmware of the drive unit may not be compatible with the battery. Contact the place of purchase to inquire about compatibility.
What does error E021 mean on Shimano Steps Bicycle Accessories?
If you see error E021 on your Shimano Steps Bicycle Accessories, the battery connected to the drive unit conforms with system standards but is not supported. Contact your place of purchase or a local bicycle dealer for assistance.
What does error E022 mean on Shimano Steps Bicycle Accessories?
If you see error E022 on your Shimano Steps Bicycle Accessories, the battery connected to the drive unit does not conform with system standards. Contact your place of purchase or a local bicycle dealer for assistance.
What to do if Shimano Steps SC-E6010 Bicycle Accessories shows temperature protection warning?
To address a temperature protection issue with your Shimano Steps Bicycle Accessories battery, leave the battery in a cool place away from direct sunlight until its internal temperature decreases sufficiently. If the problem continues, contact the place of purchase.
What does W030 error mean on Shimano Steps Bicycle Accessories?
If you encounter error W030 on your Shimano Steps Bicycle Accessories, it could be due to two or more assist switches connected to the system or a communication error between the drive unit and the motor unit. To resolve this: * Change the assist switch to the gear shifting switch, or connect only one assist switch and turn on the power again. * Check that the cable is properly connected between the drive unit and the motor unit. If the situation does not improve, contact the place of purchase.
Explanation of power assist levels (HIGH, NORMAL, ECO, OFF, WALK) and their usage.
Safe procedures for charging the system battery, including cautions.
Procedures for turning the system power on and off via computer or battery.
Instructions for activating and using the walk assist function.
Adjusting shift timing for easier or harder pedaling in automatic mode.
Interpreting lighting patterns on the battery LED for error identification.
Understanding error codes and warnings displayed on the cycle computer.
List of system warnings, their causes, and recommended solutions.
List of system error codes and the steps to resolve them.
Diagnosing and resolving issues with the power assist function.
Solutions for common problems related to the battery and charger.
Resolving issues related to the cycle computer's display and functionality.
General| Display Type | LCD |
|---|---|
| Compatibility | SHIMANO STEPS |
| Mounting | Handlebar |
| Compatible Battery | SHIMANO STEPS batteries |
| Type | E-bike display/switch unit |
| Functions | Walk mode display |
| Water Resistance | IPX6 |
To Next Page