What does error E043 mean on Shimano Steps DU-E6012 Bicycle Accessories?
If you see error E043 on your Shimano Steps Bicycle Accessories, part of the cycle computer’s firmware may be damaged. Contact the place of purchase or bicycle dealer.
Why is the gear position not displayed on my Shimano Steps DU-E6012?
If the gear position is not displayed on your Shimano Steps Bicycle Accessories, it is only displayed when the electronic gear shifting unit is installed. Check if the electric wire connector is disconnected. If you are not sure, contact the place of purchase.
How to fix system error on Shimano Steps DU-E6012 Bicycle Accessories?
If you experience a system error with your Shimano Steps Bicycle Accessories, ensure the cable is properly connected and not loose. If the problem persists, it's recommended to contact the place of purchase.
Why is assistance not being provided on my Shimano Steps DU-E6012 Bicycle Accessories?
If you're experiencing assistance issues with your Shimano Steps Bicycle Accessories, check these potential causes: * Ensure the battery is sufficiently charged and recharge if needed. * If riding on long slopes in summer or carrying heavy loads, turn off the power temporarily. * Assistance is not provided at speeds of 25 km/h or more, so check your speed. For issues related to incorrect connections or problems with the drive unit, cycle computer, or assist switch, contact the place of purchase.
Why won't the lights turn on my Shimano Steps DU-E6012 Bicycle Accessories?
If the front light or the tail light does not illuminate even when the switch is pressed on your Shimano Steps Bicycle Accessories, the E-TUBE PROJECT settings may be wrong. Contact the place of purchase.
Why doesn't the replaced battery work on my Shimano Steps DU-E6012?
If the replaced battery does not work with your Shimano Steps Bicycle Accessories, the firmware of the drive unit may not be compatible with the battery. Contact the place of purchase to inquire about compatibility.
What does error E021 mean on Shimano Steps DU-E6012?
If you see error E021 on your Shimano Steps Bicycle Accessories, the battery connected to the drive unit conforms with system standards but is not supported. Contact your place of purchase or a local bicycle dealer for assistance.
What does error E022 mean on Shimano Steps Bicycle Accessories?
If you see error E022 on your Shimano Steps Bicycle Accessories, the battery connected to the drive unit does not conform with system standards. Contact your place of purchase or a local bicycle dealer for assistance.
What to do if Shimano Steps DU-E6012 Bicycle Accessories shows temperature protection warning?
To address a temperature protection issue with your Shimano Steps Bicycle Accessories battery, leave the battery in a cool place away from direct sunlight until its internal temperature decreases sufficiently. If the problem continues, contact the place of purchase.
What does W030 error mean on Shimano Steps DU-E6012 Bicycle Accessories?
If you encounter error W030 on your Shimano Steps Bicycle Accessories, it could be due to two or more assist switches connected to the system or a communication error between the drive unit and the motor unit. To resolve this: * Change the assist switch to the gear shifting switch, or connect only one assist switch and turn on the power again. * Check that the cable is properly connected between the drive unit and the motor unit. If the situation does not improve, contact the place of purchase.
Safety information to avoid burns or injuries from leaks, overheating, fire, or explosions.
Precautions for safe operation, including attention to the cycle computer and wheel installation.
Precautions for battery handling, including eye contact, humidity, and maintenance.
Guidelines for safe usage, checking components, supervision, and battery handling.
Disposal guidelines for used batteries outside the EU.
Cleaning advice, key numbers, software updates, and chain maintenance.
Overview of system features like lightweight design, silent ride, and shifting performance.
Step-by-step guide on how to turn on, select modes, and ride the bicycle.
Explains different assist modes (HIGH, NORMAL, ECO, OFF, WALK) and their usage.
Identifies key components of the SHIMANO STEPS system with a diagram.
Lists technical specifications like temperature range, battery type, voltage, and power.
Initial setup for the battery, requiring charging before use.
Safety precautions and instructions for charging the battery.
Step-by-step guide for charging the battery when it's not on the bicycle.
Further instructions for charging specific battery models.
Detailed steps for connecting charging plugs for specific battery models.
Instructions for charging the battery while it is attached to the bicycle.
Explains the meaning of the LED indicator on the charger.
Explains the meaning of the LED indicator on the battery.
Details on how the battery LED indicates charging status and level.
Shows how battery levels are displayed on the cycle computer.
Guidelines for charging the battery and storage for long periods.
Step-by-step instructions for installing the battery into the mount.
Instructions for installing the BT-E8020 battery model.
Steps to remove the battery using the key for BT-E6000/E6001/E6010/E8010 models.
Instructions for removing the BT-E8020 battery model.
How to use buttons on assist and shifting switches for operations.
Guide on how to attach and detach the cycle computer from its bracket.
Instructions for turning the system power on and off via the computer or battery.
Describes the logo screen displayed during system startup and shutdown.
Explains the elements and data shown on the basic cycle computer screen.
Shows how battery levels are displayed on the cycle computer for different models.
How to change the assist mode using the assist switch buttons.
Steps to activate the walk assist mode.
How to use and stop the walk assist function.
How to view gear position and traveling data using the assist switch.
Details on displayed traveling data like distance, range, time, and speed.
How to control the battery-powered light using the cycle computer buttons.
How to switch between automatic and manual gear shifting modes.
Steps to clear traveling distance (DST) and other related data.
How to access the settings menu by pressing specific buttons.
Navigating and selecting configurable items in the settings menu.
Options to clear traveling distance or reset display settings to default.
Steps to set the hour and minute for the clock.
How to set the starting gear for the start mode function.
How to configure the display backlight setting (ON, OFF, MANUAL).
How to adjust the backlight brightness to one of 5 levels.
How to turn the beep sound on or off.
How to switch between kilometers (km) and miles for distance units.
How to configure the display language setting.
How to change the font color (White or Black).
Adjusting gear shifting only for electronic gear shifting units.
Adjusting shift timing for easier pedaling in automatic mode.
How to close the setting menu and return to the basic screen.
Information on automatic backup and operations that may prompt an update.
How to download and use the E-TUBE PROJECT for configuration and firmware updates.
Explains error indications based on battery LED patterns and their remedies.
Lists warning codes, preconditions, restrictions, and remedies.
Details specific warning codes like W010, W011, W012 and their solutions.
Procedures for resetting error messages displayed on the entire screen.
Lists error codes like E010, E012, E013 and their remedies.
Lists error codes E014, E020, E021, E022, E030, E031, E033, E043 and their remedies.
Lists symptoms, causes, and remedies for issues with the assist function.
Addresses symptoms like stiff pedaling and low battery assistance.
Lists symptoms, causes, and remedies for battery issues like quick discharge or not recharging.
Further battery issues like warm charger, LED not illuminating, and removal problems.
Troubleshooting for the front or tail light not illuminating.
Symptoms and remedies for the cycle computer not displaying or starting.
Troubleshooting for switch operation, beeps, assistance weakening, and noises.
General| Max Torque | 50 Nm |
|---|---|
| Weight | 3.2 kg |
| Compatible with Chain Case | Yes |
| Internal Gear Hub Compatible | Yes |
| Series | STEPS |
| Motor Type | Brushless motor |
| Rated Power | 250W |
| Battery Compatibility | BT-E6010 |
| Rated Voltage | 36V |
| Assist Modes | Eco, Normal, High |
| Maximum Assist Speed (km/h) | 25 km/h |
| Position | Mid-ship |
| Compatible Brake Type | Disc |
| Compatible Bottom Bracket | Shimano Steps specific |
To Next Page
