Why is my Shott BP-35WS-B Heat Pump leaking water?
If water is leaking from your Shott Heat Pump, it could be due to condensation accumulation. Put the heat pump in standby; if the leak stops, it's normal condensation. It could also be a water leak from the water exchanger or hydraulic unit connections; tighten the fastening nut.
What does error message EE 9 on my Shott BP-35WS-B mean?
If your Shott Heat Pump is showing error message EE 9, it could indicate several issues: the high or low pressure sensor might be incorrectly connected or defective, so check the connections and replace if necessary. The pool temperature or ambient temperature might be too high, so wait until they drop. The capillary circuit could be clogged, requiring replacement. Also, it's possible that manual defrost was started without frost on the plate heat exchanger; in this case, turn the unit off, then on, and start the pump.
What does error message EE c on my Shott BP-35WS-B Heat Pump mean?
If your Shott Heat Pump displays error message EE c, it indicates that the ambient temperature is under -15 [°C] or lower than the minimum working temperature. Wait until the ambient temperature rises to start the heat pump or set the minimum working temperature again.
What does error message EE d on my Shott Heat Pump mean?
If your Shott Heat Pump shows error message EE d, it means functional parameter changes have occurred, and Parameter 9 is not set to 0. Set the correct parameter value to 1 or replace the control board.
What to do if there is frost on the plate heat exchanger of my Shott Heat Pump?
If there's frost on the plate heat exchanger of your Shott Heat Pump, it could be due to low ambient temperature or high humidity. Start manual defrost. Also, a drop in refrigerant pressure could be the cause, so verify leakage and replace refrigerant if needed.
What to do if my Shott BP-35WS-B Heat Pump does not work and error message EE 7 is displayed?
If your Shott Heat Pump displays error message EE 7 and isn't working, it indicates current dispersion. Replace the defective component, such as the compressor, fan, four-way valve, or electronic board.
Declaration of conformity with relevant EU directives and harmonised standards.
Details the general terms and conditions of the product warranty.
Outlines specific conditions for warranty validity and coverage.
Lists limitations and exclusions applicable to the warranty coverage.
Describes the intended use and application of the SERIES BP heat pumps.
Instructions for inspecting the heat pump upon delivery and checking packaging integrity.
Guidelines for safely handling the heat pump unit during installation and unpacking.
Specifies requirements and considerations for selecting the optimal installation location.
Details on selecting a suitable support and the installation site requirements.
Guidelines for the proper disposal of packaging and replaced parts.
Instructions for safely decommissioning and disposing of the heat pump at end-of-life.
Important warnings and recommendations for performing hydraulic connections safely.
Illustrates the general layout for connecting the heat pump within the pool's hydraulic system.
Crucial precautions to be taken before starting the heat pump system.
Essential checks to perform before the very first start-up of the heat pump.
Overview of the heat pump's control system and its energy-saving features.
Detailed explanation of the heat pump's control panel and its interface.
Instructions on how to safely turn on the heat pump using the protection device.
Explanation of the heat pump's standby mode and what is displayed.
Procedure for safely turning off the heat pump.
Sets the acceptable range for pool water temperature regulation.
Configures the ambient temperature at which automatic defrost begins.
Sets the heat exchanger temperature for stopping the automatic defrost cycle.
Determines the interval between automatic defrost cycles.
Sets the time duration for both automatic and manual defrost cycles.
Configures the maximum temperature limit for compressor protection.
Enables automatic restart of the previous operating mode after a power outage.
Selects the primary operating mode of the heat pump (heating, cooling).
Sets the maximum allowed deviation from the target pool temperature.
Selects the control mode for the heat pump or heater.
Describes the sensors and devices that control the heat pump's operation.
Information on ambient and pool water temperature sensors and their function.
Details the flow sensor used to monitor water flow rate.
Describes sensors for monitoring compressor and heat exchanger temperatures.
Explains the function of the high pressure sensor in protecting the compressor.
Details the low pressure sensor and its role in compressor protection.
Periodic checks and maintenance tasks that users can perform.
Maintenance tasks that require a qualified technician.
Instructions for protecting the heat pump during the winter season.
Steps for recommissioning the heat pump after winter storage.
Important notes and procedures before replacing parts on the heat pump.
Instructions for safely replacing the manometer on the heat pump.
Procedure for replacing the pressure sensor, including necessary tools.
Guidelines for replacing the filter and capillary components.
Troubleshooting step for frost on the radiator, involving refrigerant pressure check.
To Next Page
General
