Siemens FC901-R3 - Power Supply Mounting

83 pages

To Next Page

To Previous Page

Power Supply Mounting

Secure the power supply to the back of enclosure using the four provided #8-32 x 3/8 screws.

AC Input terminals must be located at the right side of the enclosure.

Main Page

Default Chapter4
- Table of Contents4
Introduction8
Control Panel Limitations8
Preface9
FCC Part 68 Warning9
Descriptions11
Fc901 System Description11
- Power Supply11
- Signaling Line Circuit (SLC)12
- Notification Appliance Circuits12
- Serial Interface Circuit12
- Status Relays12
- Programming Port12
- Dact12
Optional Modules12
- City Tie Module (FCI2020-U1)12
- Battery Sets12
- Remote Printer Module (FCA2018-U1)12
Auxiliary Modules13
- Serial LCD Annunciators13
- FT Series LED Driver/Annunciators13
Slc Addressable Devices14
- Smoke Detector14
- Heat Detectors14
- Addressable Modules (Monitor and Control)14
- Manual Stations14
- Sounder Base14
- Programming SLC Devices15
Event History16
General Design Features17
- Environmental17
- Power Limiting17
- Ground Fault Detection17
- NAC Operation17
- Security Features17
Regulatory Standards18
- Underwriters Laboratories18
- Federal Communications Commission18
General Specifications19
- Environmental19
- Primary Power Supply19
- Secondary Power Supply19
- Auxiliary Power Outputs19
- Status Relays20
- Notification Appliance Circuits20
- Serial Interface Circuit20
- SLC Addressable Device Circuits20
- City Tie Circuits20
- DACT Circuits21
Control Panel Operation22
Operation Instructions22
- Standby Condition22
- Alarm Conditions22
- Trouble Conditions23
- Supervisory Conditions23
Additional Operating Procedures25
- Lamp Test25
- History25
Fc901 Operating Instructions26
- Alarm Operation26
- Authorized Personnel Only26
- Trouble Operation26
- Event Scrolling26
- Fuse Replacement and Battery Maintenance26
Fsd901 Operating Instructions27
- Alarm Operation27
- Authorized Personnel Only27
- Trouble Operation27
- Event Scrolling27
- Normal Standby Condition27
Control Panel Installation28
Parts Supplied - Fc90128
- FC901 Enclosure Package28
- FC901 Main Board Package28
  - FC901 Configuration Kit Package29
Cautions30
Control Panel Location30
Installation30
- Enclosure Mounting30
- Remove Knock-Outs33
- Power Supply Mounting34
- Ground Wire Installation35
- Battery Installation36
- Optional City Tie Mounting37
- Main Board Assembly Installation38
- Earth Cable Installation38
System Wiring39
- AC Connection39
- Battery Connection39
Wiring39
- Control Panel Wiring Overview40
- Wiring Entering Enclosure40
- Install Wiring40
- Wiring Separation41
- Internal Structure42
- Power Supply and Battery Wiring43
- Status Relays44
- Auxiliary Power Outputs Wiring44
- NAC Wiring45
- Serial Interface Circuit46
- Serial Remote Device Wiring Overview47
- SLC Addressable Device Circuit48
- SLC Addressable Device Wiring Diagrams49
- Optional City Tie/Leased Line51
- DACT Wiring51
Programming the Control Panel52
Keypad Programming52
Pc Programming52
Programming Security52
Maintenance53
General53
Quick Test54
Appendix-A: Reference Data56
Wire Selection Guides56
- Resistance of Solid Copper Wire56
- Addressable Device Circuit Wire Selection Guide56
Battery Size Calculations57
- System Current Draw Break down57
- SLC Current Draw Break down57
- Battery Size58
Appendix-B: Compatible Devices59
- Devices for Addressable Device Circuits59
- Siemens SLC Manual Pull Stations59
- Siemens SLC Modules59
- Siemens SLC Bases59
- Siemens SLC Accessories59
- 8700 SLC Manual Pull Stations60
- 8700 SLC Detectors60
- 8700 SLC Modules60
- 8700 SLC Bases60
- 8700 SLC Accessories60
- Fd182Ul60
- Global ASA61
- UFP Devices61
Appendix-C: Troubleshooting62
- General62
- System Events62
Appendix-D: Alarm Verification63
Appendix-E: Application Specific Detection64
Appendix-F: Testing/Maintenance65
Appendix-G: Lcd, Controls and Indicators66
- Communication Port Connector66
- LEDS, Buzzer and Dedicated Push Buttons66
- LCD Display69
Appendix-H: Output Features70
- Output Activation- and Deactivation- Delays70
Appendix-I: Pas / Pre-Signal71
- Pas71
- Pre-Signal72
Appendix-J: Dact Information Overview73
Appendix-K: Drift Compensation79
Appendix-L: Glossary80

Siemens FC901-R3 - Power Supply Mounting

Table of Contents

Related product manuals