Siemens iQ300 SN73HX42VG User Manual

en Water softening system
24
Water hardness
°E
Hardness range mmol/l Setting value
0 - 8 Soft 0 - 1.1 H00
9 - 10 Soft 1.2 - 1.4 H01
11 - 12 Medium 1.5 - 1.8 H02
13 - 15 Medium 1.9 - 2.1 H03
16 - 20 Medium 2.2 - 2.9 H04
21 - 26 Hard 3.0 - 3.7 H05
27 - 38 Hard 3.8 - 5.4 H06
39 - 62 Hard 5.5 - 8.9 H07
Note:Set the water hardness determ-
ined on your appliance.
→"Setting the water softening sys-
tem", Page24
With a water hardness of 0 - 8°E
you can dispense with special salt for
dishwashers and switch off the water
softening system.
→"Switching off the water softening
system", Page25
10.2 Setting the water soften-
ing system
Set the water hardness on your appli-
ance.
1. Determine the water hardness and
the appropriate setting value.
→"Overview of water hardness set-
tings", Page23
2. Press ⁠.
3. To open the basic settings, press
for 3 seconds.
a The display shows Hxx.
a The display shows ⁠.
4. Press repeatedly until the
right water hardness has been set.
The value H04 is set at the factory.
5. To save the settings, press
for 3 seconds.
10.3 Special salt
You can use special salt to soften
water.
Adding special salt
If the special salt refill indicator lights
up, add special salt to the dispenser
for special salt just before the pro-
gramme starts. The consumption of
special salt depends on the water
hardness. The higher the water hard-
ness, the greater the consumption of
special salt.
ATTENTION!
Detergent may damage the water
softening system.
▶ Only fill the dispenser of the water
softening system with special dish-
washer salt.
Special salt for dishwashers can
damage the tub due to corrosion.
▶ To make sure that any special salt
that escapes is washed out of the
tub, add the special salt to the dis-
penser for special salt immediately
before the programme starts.
1. Unscrew the lid of the dispenser
for special salt and remove.
2. On initial start-up: Fill the dispenser
right up with water.

Siemens iQ300 SN73HX42VG Specifications

General

Door color	Not applicable
Cord length	1.75 m
Control type	Buttons
Product size	Full size (60 cm)
Inlet hose length	1.65 m
Custom panel-ready	Yes
Outlet hose length	1.9 m
Appliance placement	Fully built-in
Control panel color	Black, Stainless steel
Current	10 A
Connected load	2400 W
AC input voltage	220-240 V
AC input frequency	50-60 Hz
Energy efficiency scale	A to G
Water consumption per cycle	9.5 L
Energy consumption per cycle	0.94 kWh
Cycle time	225 min
Noise level	46 dB
Drying system	Heat exchanger
Delay start (max)	24 h
Overflow protection	-
Dishwashing programs	60min 65°C, Auto 45-65°C, Eco 50°C, Favorite, Intensive 70°C, Quick
Number of place settings	13 place settings
Number of washing programs	6
Package weight	39000 g
Apps supported	Siemens Home Connect
Feet adjustment	60 mm
Automatic door opening	No

Weight and Dimensions

Depth	550 mm
Width	598 mm
Height	815 mm
Weight	36900 g
Depth with door open	1150 mm
Installation compartment depth	500 mm
Installation compartment width	600 mm
Installation compartment height (max)	875 mm