Siemens S120 - Page 19

Siemens S120_EN_rev06-08062017.docx 3-14
Table 5 Technical data PM340, FSE and FSF (3 AC 380 V to 480 V ±10 %)
PM340
6SL321
0-
1SE27-
5UA0
1SE31-
0UA0
1SE31-
1UA0
1SE31-
5UA0
1SE31-
8UA0
PM340 with integrated line filter
6SL321
0-
1SE27-
5AA0
1SE31-
0AA0
1SE31-
1AA0
1SE31-
5AA0
1SE31-
8AA0
Frame size
FSE
FSE
FSF
FSF
FSF
Output current
Rated current In
Base-load current IH
for S6 operation (40 %) Is6
Peak current Imax
A
A
A
A
75
65
98
124
90
80
117
150
110
95
143
180
145
115
188
220
178
155
231
290
Type rating¹)
on basis of In
on basis of IH
kW
kW
37
30
45
37
55
45
75
55
90
75
Rated pulse frequency
kHz
4
4
4
4
4
Power loss
kW
0.99
1.21
1.42
1.93
2.31
Cooling air requirement
m³/s
0.022
0.039
0.094
0.094
0.117
Sound pressure level LpA (1m)
dB
<60
62
<60
<60
65
24 V DC supply
for the Control Unit
A
1.0
1.0
1.0
1.0
1.0
Rated input current²)
with/without integrated line
reactor
A
78/88
94/105
115/129
151/168
186/204
Class J UL fuses
Rated current
Short-circuit current rating SCCR
A
kA
3NE1021-0
100
65
3NE1022-0
125
65
3NE1224-0
150
65
3NE1225-0
200
65
3NE1227-0
250
65
NH fuses IEC 60947
Rated current
A
3NA3830
100
3NA3832
125
3NA3836
160
3NA3140
200
3NA3144
250
Circuit breaker type
designation IEC 60947
Rated current
A
3VL1712-
1DD33-
0AA0
100 …125
3VL1716-
1DD33-
0AA0
125 … 160
3VL3720-
1DC36-
0AA0
160 … 200
3VL3720-
1DC36-
0AA0
160 … 200
3VL3725-
1DC36-
0AA0
200 … 250
Resistance value
ext. braking resistor
Ω
>15
>8.2
Max. cable length
to braking resistor
m
15
Line supply connection
L1, L2, L3
Screw terminals for
cable cross-sections 10 …
50mm²
Screw terminals for
cable cross-sections 120mm²
Motor connection
U2, V2, W2
DC link connection, connection
for braking resistor DCP/R1,
DCN, R2
PE connection
On housing with M6 screw
On housing with M8 screw
Max. motor cable length ³)
shielded/unshielded
m
70 / 100
Degree of protection
IP20 or IPXXB
Height
PM340 with/without integrated
line filter
mm (in)
498.3 (19.62) / 633
(24.92)
634 (24.96) / 934 (36.77)
Weight
with/without integrated line filter
kg
19.8 / 27.1
50.7 / 667
¹) Rated power of a typical standard induction motor at 400 V 3 AC
²) The input current depends on the motor load and line impedance. The input currents apply for a load with
the type rating (based on Irated) for a line impedance corresponding to uk = 1%.
³) Max. motor cable length 25 m (shielded) for PM340 Power Modules with integrated line filter to maintain
the limit values of EN 61800-3 Category C2.