Siemens SINAMICS G120C - Page 43

Commissioning
4.2 Commissioning with BOP-2 operator panel
SINAMICS G120C converter
Getting Started, 04/2014, FW V4.7, A5E34264105B AA
43
No.
Description
.13
External fault 1 (F07860)
.15
CDS bit 1
r0056
CO/BO: Status word, closed-loop control
r0060 CO: Speed setpoint before setpoint filter
[100 % ≙ p2000]
r0062
CO: Speed setpoint after filter [100 % ≙ p2000]
r0063 CO: Speed actual value unsmoothed
[100 % ≙ p2000]
r0064 CO: Speed controller system deviation
[100 % ≙ p2000]
r0065
Slip frequency [100 % ≙ p2000]
r0066
CO: Output frequency [100 % ≙ p2000]
r0067
CO: Output current, maximum [100 % ≙ p2002]
r0068 CO: Absolute current actual value unsmoothed
[100 % ≙ p2002]
r0070
CO: Actual DC link voltage [100 % ≙ p2001]
r0071 Maximum output voltage [100 % ≙ p2001]
r0072
CO: Output voltage [100 % ≙ p2001]
r0075 CO: Current setpoint field-generating
[100 % ≙ p2002]
r0076 CO: Current actual value field-generating
[100 % ≙ p2002]
r0077 CO: Current setpoint torque-generating
[100 % ≙ p2002]
r0078 CO: Current actual value torque-generating
[100 % ≙ p2002]
r0079
CO: Torque setpoint, total [100 % ≙ p2003]
r0080
CO: Actual torque value
[0]
unsmoothed
[1]
smoothed
r0082
CO: Active power actual value
[0] unsmoothed [1] smoothed with
p0045
[2]
Electric power
p0100
IEC/NEMA motor standard
0 IEC motor (50 Hz, SI units)
1
NEMA motor (60 Hz, US units)
2
NEMA motor (60 Hz, SI units)
p0124
CU Identification via LED
p0133
Motor configuration
.00 1: Delta
0: Star
.01 1: 87 Hz
0: No 87 Hz
p0170
Number of Command Data Sets (CDS)
p0180
Number of Drive Data Sets (DDS)
No.
Description
p0201
Power unit code number
r0204
Power unit, hardware properties
p0205
Power unit application
0
Load cycle with high overload
1
Load cycle with light overload
r0206
Rated power unit power [kw/hp]
r0207
Rated power unit current
r0208
Rated power unit line supply voltage [V]
r0209
Power unit, maximum current
p0210
Drive unit line supply voltage [V]
p0219 Braking resistor braking power [kW]
p0230
Drive filter type, motor side
0
No filter
1
Motor reactor
2
dv/dt filter
3
Siemens sine-wave filter
4
Sine wave filter, third-party manufacturer
p0233
Power unit motor reactor [mH]
p0234
Power unit sine-wave filter capacitance [µF]
r0238
Internal power unit resistance
p0287 Ground fault monitoring thresholds
[100 % ≙ r0209]
r0289 CO: Maximum power unit output current
[100 % ≙ p2002]
p0290
Power unit overload response
0
Reduce output current or output frequency
1 No reduction, shutdown when overload
threshold is reached
2 Reduce I_output or f_output and f_pulse (not
using I2t).
3
Reduce the pulse frequency (not using I2t)
12 I_output or f_output and automatic pulse
frequency reduction
13
Automatic pulse frequency reduction
p0292
Power unit temperature alarm threshold [°C]
p0295
Fan run-on time [s]
p0300
Motor type selection
0
No motor
1
Induction motor
2
Synchronous motor