To Next PageTo Next Page
Need help?Do you have a question about the Siemens SINAMICS V10 and is the answer not in the manual?
General| Control Method | V/f control |
|---|---|
| Degree of protection | IP20 |
| Relative Humidity | 5 % to 95 % (non-condensing) |
| Altitude | Up to 1000 m above sea level without derating |
| Frequency | 50 Hz / 60 Hz |
| Protection | Overcurrent, overvoltage, undervoltage, overload, short circuit, ground fault |
| Communication | RS485 |
| Operating Temperature | -10°C to +50°C |
| Power Range | 0.37 kW to 4 kW |
| Storage Temperature | +70 °C |
| Input Voltage | 1-phase: 200-240V AC, 3-phase: 380-480V AC |
Explains the manual's objective for customers regarding the SINAMICS V10 inverter.
Provides links for updated product information and user documentation for the SINAMICS V10.
Directs users to contact local distributors for product-related questions and assistance.
General safety instructions for handling the inverter and connected equipment.
Safety precautions for electrical connections to the inverter.
Safety notes related to the commissioning phase of the inverter.
Safety advice for troubleshooting operations involving the inverter.
Guidelines for safe and environmentally compliant disposal of equipment.
Provides a general overview of the SINAMICS V10 inverters and their capabilities.
Lists main characteristics, performance, and protection features of the inverter.
Details the components included in the SINAMICS V10 inverter package.
Explains the structure and meaning of the inverter's MLFB order number.
Lists available optional components for the inverter system.
Lists available spare parts for the SINAMICS V10 inverter.
Covers all aspects of the physical installation of the inverter.
Specifies correct mounting orientation and required clearances for ventilation.
Provides instructions and dimensions for mounting the inverter directly onto a wall.
Details how to detach and mount the operator panel onto a cabinet door.
Covers the electrical connection and wiring of the inverter.
Shows the layout of PE terminals across different frame sizes.
Illustrates the arrangement of various connection interfaces on the inverter.
Describes the communication interface between the inverter and its operator panel.
Specifies recommended conductor sizes for input and output cables.
Details conductor sizes for digital and analog I/O connecting cables.
Explains how to connect the power supply and motor to the inverter.
Describes various typical wiring configurations for the inverter.
Details the basic out-of-box connection mode for the inverter.
Describes connection mode C02 for LOC/REM control.
Describes connection mode C03 for operator panel and external potentiometer control.
Describes connection mode C04 for external control of start/stop, direction, and speed.
Describes connection mode C05 for combined operator panel and external control.
Describes connection mode C06 for external control of start/stop, direction, and frequency.
Describes connection mode C07 for PLC control.
Describes connection mode C08 for PLC and external signal control.
Describes connection mode C09 for JOG mode control.
Describes connection mode C10 for MOP/feedback control.
Describes connection mode C11 for operator panel speed control.
Explains pre-defined application macros for different motor control scenarios.
Provides an overview and explanation of the operator panel functions and buttons.
Details the function of each label, key, and display on the operator panel.
Explains the different types of data displays shown on the operator panel.
Guides the user through the initial setup and configuration process.
Explains how to view the inverter's operational status.
Introduces different operational modes for parameter access and configuration.
Describes the mode for setting essential motor parameters.
Explains how to select connection macros for specific wiring configurations.
Details how to select pre-defined application macros.
Allows setting parameters specific to common application macros.
Provides access to all inverter parameters for reading and setting.
Explains how to reset the inverter to its factory default settings.
Guides on uploading and downloading parameter sets between inverters and the operator panel.
Lists parameters related to the inverter's current operational status.
Parameters for configuring motor characteristics during initial setup.
Parameters related to the configuration of digital inputs and outputs.
Parameters for configuring analog inputs and outputs.
Parameters related to setting the frequency reference source.
Parameters that control the inverter's operational behavior.
Parameters for configuring various protection functions.
Miscellaneous parameters not covered in other specific groups.
Allows defining a custom set of parameters accessible to the user.
Configures the inverter's reaction to internal over-temperature.
Sets the nominal motor current from the rating plate.
Selects the function for digital input 1.
Allows setting the proportion gain for the PI controller.
Shows default parameter values based on selected connection macros.
Steps to acknowledge and clear fault codes displayed by the inverter.
Lists fault codes, their possible causes, and diagnostic steps.
Lists and explains alarm codes and their possible causes and remedies.
Detailed technical specifications for the SINAMICS V10 inverter across frame sizes.
Provides outline dimensions, weight, and mounting methods.
Specifies operating and storage environmental conditions.
Details ambient temperature limits for operation and derating.
Specifies the protection class of the inverter and lists compliance with standards.
Step-by-step guide to removing fans from Frame Size B inverters.
Step-by-step guide to removing fans from Frame Size C inverters.
Step-by-step guide to removing fans from Frame Size D inverters.
