Siemens SINEC L2 User Manual

System Description S5-95U, SINEC L2
1.4 Assigning Parameters for the L2 Interface of the S5-95U
You assign the parameters for the L2 interface in DB1, in the parameter block with block ID “SL2:”.
Irrespective of the type of data transmission you select, you must assign certain parameters (basic
parameters) in DB1. The basic parameters affect only the procedures for accessing the network
(see section 1.3) and not the communication mechanisms. DB1 has default settings for the basic
parameters that you can use or change according to the task to be performed.
The default DB1 is illustrated in Figure 1-6.
Figure 1-6. DB1 with the Default Parameters
0: KS ='DB1 0BA: AI 0 ; 0BI: ';
12: KS =' ; 0BC: CAP N CBP ';
24: KS ='N ;#SL1: SLN 1 SF ';
36: KS ='DB2 DW0 EF DB3 DW0 ';
48: KS =' CBR FY100 CBS FY1';
60: KS ='01 PGN 1 ;# SDP: N';
72: KS ='T 128 PBUS N ; TFB: OB13';
84: KS =' 100 ; #CLP: STW MW10';
96: KS ='2 CLK DB5 DW0 ';
108: KS =' SET 3 01.10.91 12:00:';
120: KS ='00 OHS 000000:00:00 ';
132: KS =' TIS 3 01.10. 12:00:00 ';
144: KS =' STP Y SAV Y CF 00 ';
156: KS =' #SL2: TLN 0 STA AKT';
168: KS =' BDR 500 HSA 10 TRT ';
180: KS ='5120 SET 0 ST 400 ';
192: KS ='SDT 1 12 SDT 2 360 SF';
204: KS =' DB6 DW0 EF DB7 DW0 ';
216: KS =' KBS MB62 KBE MB63 ; ';
228: KS ='# END ';
Basic parameters
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a
Parameters for type of data transmission
( Chapters. 4, 6, 7 and 8)
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Parameters for S5-95U
functions described in the
S5-90U/S5-95U system
manual
The basic parameters and their ranges are listed and explained in the following Table.
1-8 EWA 4NEB 812 6112-02

Siemens SINEC L2 Specifications

General

Brand	Siemens
Model	SINEC L2
Category	Controller
Language	English