Silverline 633488 - Introduction; Description of Symbols; Safety Instructions; Before Cutting

GB
4
Specication
Equipment Required
Inordertousethisworktopjig,ALLofthefollowingitemsarerequired:
• ½"router–minimum1600Wmotor
• Non-bevelledworktopjigguidebushwith30mmouterdiameter
• Tungstencarbideroutercutter–12.7x50mm
• OnepairofG-clamps
Note:Ensurethatyouhavemountedaguidebushonyourrouterthathasanouterdiameterof
30mm.Refertothemanualoftheroutermanufacturerforadviceonaccessoriesandguidebush
installation.
Product Familiarisation
1 Carry Handle
2 Peg Holes For Different Worktop Sizes
3 Centre Slot
4 Female Peg Holes
5 Male Peg Holes
6 Joint Bolt Holes
7 Bolt Peg Holes
Types of Cut
90° STANDARD LEFT HAND JOINTCORNER JOINT
PENINSULAR JOINT
90° STANDARD RIGHT HAND JOINT
MALE
MALE
FEMALE
FEMALE
MALE
MALE
MALE
MALE
FEMALE
FEMALE
90˚ Left Hand Joint
Left Hand Female Cut
• Theworktopmustbeplacedwiththesurfacefaceupandthepost-formed(front)edgefacingyou
• Withthejigfacingup,placetwoplasticpegsinthecountersunkFemalePegHoles(4)which
areindicatedbyan'F'
• Placeanotherpegintotherelevanthole.Thiswilldependonthewidthoftheworktopbeing
used
• Positionthejigovertheworktopedge(asshown),beforesecuringthejigintopositionwith
G-clamps
• Placetherouteronthelefthandside.Alwayscutfromlefttoright
• Onlycuttoan8mmdepthwitheachpass.Repeattheprocessuntilthecutiscomplete
• Makeoneextrapassacrossthecuttocleanoffexcessmaterial
FEMALE
Description of Symbols
Theratingplateonyourtoolmayshowsymbols.Theserepresentimportantinformationaboutthe
productorinstructionsonitsuse.
Wearhearingprotection.
Weareyeprotection.
Wearbreathingprotection.
Wearheadprotection.
Wearhandprotection.
Readinstructionmanual.
Introduction
ThankyouforpurchasingthisSilverlinetool.Thismanualcontainsinformationnecessary
forsafeandeffectiveoperationofthisproduct.Thisproducthasuniquefeaturesand,evenif
youarefamiliarwithsimilarproducts,itisnecessarytoreadthismanualcarefullytoensure
youfullyunderstandtheinstructions.Ensureallusersofthetoolreadandfullyunderstand
thismanual.
Original Instructions
Safety Instructions
Before Cutting
• Itisessentialtofamiliariseyourselffullywiththecorrectprocedureforsettingupthejigbefore
attemptingtostartthecut
• Beforeusingthisjigwerecommendthatyouperformafewpracticejointswithoff-cutsof
worktopsorothermaterialstofamiliariseyourselfwiththejig
• Childrenandanimalsshouldalwaysbekeptatasafedistancefromyourwork.Makeyourwork
areachildproof
• Alwaysunplugyourpowertoolsfromthemainspowersupplybeforesettingup,changing
accessories,makingadjustmentsormaintenance
• Alwaysconnectyourrouterandotherpowertoolstoadustextractionsystem,tomaintainasafe
andcleanworkenvironment
• Sweepawayresidualsawdustaftereachcuttopreventtheworkareafrombecomingslippery
• Alwaysensurethattheworktopissupportedproperlyandsecuredrmlytoabenchortrestle
beforecutting
• Ensurethatthejigisrmlyclampedtothesurfaceoftheworktop
• Makesuretheworkareaiscompletelyclearsothatthereisthemaximumamountofworkspace
available
• Eachcutshouldbemadefromlefttoright
• Thecuttermustalwaysenterthroughthepost-formed(front)edge,exceptwhenproducingthe
boltholes
• Whenplungingtherouter,makesureeachcutisamaximumof8mmdeep
• Donotuseabluntroutercutterasthiswillseverelyaffectthequalityofthenaljoint
During Cutting
• •Alwayswearadequatepersonalprotectionequipment,includingeyeprotection,eardefenders
andadustmask,whensettingupandusingarouterandotherpowertools
• •Makesurethatthepathoftherouteriskeptclearofanyobstructions
• •Makesurethatthepegsarermlyinpositionandarenotproudofthejig'ssurface
• •Ensurethatthepowercableoftherouterisclearofthejigandisofsufcientlength
• •Alwaysensurethecutterisnottouchingtheworkpiecewhenstartingtherouter
• •Donotforcetheroutertoworktoofast.Thiswillresultinapoorqualitynishandcandamage
theroutercutter
• •Allowthecuttertocometoacompletestopbeforeremovingtherouterfromthejig
• •Alwayskeeptherouterbaseatonthejig'ssurface.Failuretodosocouldresultinthejoints
notmatchingup
• •Donotover-reachthejig.Keepastablefootingatalltimes
633488_Manual.indd 4 15/06/2017 15:54