Sinoboom 4047E - Table of Contents

GTJZ0612E&0812E&1012E&1212E Operation Manual i © Jun 2020
TABLE OF CONTENTS
Introduction ............................. iii
1 Performance Parameters ...... 1-1
2 Machine Components .......... 2-1
3 Safety ............................... 3-1
Safety Definitions ...... . . . . . . . . . . . . . . . 3-1
Reporting Accidents........ . . . . . . . . . . . 3-1
Electrocution Hazards. . . . . . . . . . . . . .... 3-1
Tipping Hazards and Rated Load .. . . . 3-2
Work Environment Hazards. . . . . ...... 3-4
Unsafe Operation Hazards. . . . . . . . . . . . 3-5
Fall Hazards. . . ...... . . . . . . . . . . . . . . . . . . 3-6
Collision Hazards . ......... . . . . . . . . . . . 3-7
Crush Hazards . . . . . . . . . . . ....... . . . . . . 3-8
Explosion and Fire Hazards. . . . . . . . . . . 3-8
Damaged Machine Hazards . . . . . . . . . . 3-8
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 3-8
Battery Hazards . . . . . . . . . . . . . . . . ...... . 3-9
Charging the Battery..... . . . . . . . . . . . 3-9
Handling the Battery . . . . . . . . . . ...... 3-9
Welding and Polishing Requirements . 3-9
After Using the Machine.. . . . . . . . .....3-10
4 Jobsite Inspection............... 4-1
5 Pre-operation Inspection ...... 5-1
Tips for Conducting a Pre-operation
Inspection . . . . . . . . . ......... . . . . . . . . . . . 5-1
Conducting a Pre-operation
Inspection . . . . . . . . . ......... . . . . . . . . . . . 5-1
Inspecting Parts . . . . . . . . . . . . . . ...... . . . 5-2
Inspecting Entire Machine . . . . . . ...... 5-2
Inspect Hydraulic Oil Level. . . . . . . . . . . . 5-2
Inspecting the Battery . . . . . ........ . . . . 5-2
6 Pre-operation Function Test .. 6-1
Preparing for a Pre-operation Func-
tion Test . . . . . . . . . . . . . ....... . . . . . . . . . . . 6-1
Testing the Ground Controller. . . . . . . . . 6-1
Testing the Ground Controller
Function . . . . . . . . ....... . . . . . . . . . . . . . 6-2
Testing the Emergency Stop
Function . . . . . . . . ....... . . . . . . . . . . . . . 6-2
Testing the Lifting and Lowering
Functions . . . . . . . . . . . . . . ......... . . . . 6-2
Testing the Platform Controller . . . . . . . . 6-2
Testing the Platform Controller .. . . . 6-3
Testing the Emergency Stop
Function . . . . . . . . ....... . . . . . . . . . . . . . 6-3
Testing the Horn . . . . . . . . . . . . . . ...... 6-3
Testing the Enabling Key Function.. 6-3
Testing the Lifting and Lowering
Functions . . . . . . . . . . . . . . ......... . . . . 6-4
Testing the Steering Function. ...... 6-4
Testing the Driving and Braking
Functions . . . . . . . . . . . . . . ......... . . . . 6-4
Testing the Drive Speed. . ......... . . . . 6-4
Testing the Emergency Lowering
Function. . . . . . . . . . . . . . . . . . ...... . . . . . . . 6-5
Testing the Tilt Protection Function . . . 6-5
Testing the Pothole Guard ........ . . . . 6-6
Testing the Weighing System
(optional) . . . . . ....... . . . . . . . . . . . . . . . . . . 6-6
7 Operating the machine ......... 7-1
Using the Emergency Stop Function . 7-1
Using the Emergency Lowering
Feature. . . . . . . . . . . . ........ . . . . . . . . . . . . 7-1
Using the Emergency Pull/Drag
Feature. . . . . . . . . . . . ........ . . . . . . . . . . . . 7-1
Operating on the Ground. . . . . . . . ...... 7-2
Operating on the Platform. . . . . . . ...... 7-2