Skytech Smart Batt III User Manual

REV. 8-7-17 Page 1
Skytech: Smart Batt III
Model: Smart Batt III
INSTALLATION AND OPERATION INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO
NOT ATTEMPT TO INSTALL OR OPERATE
INTRODUCTION
This remote control system was developed to provide safe, reliable, user-friendly operation for gas heating appliances. This is a dry
contact, thermostat controlled system with built-in timer that can be operated from the transmitter.
The transmitter operates on (2) AAA 1.5V batteries that are included. Install the AAA
batteries supplied with the unit into the battery compartment. It is recommended
that ALKALINE batteries always be used for this product. Be sure the batteries are
installed with the (+) and (-) ends facing the correct direction.
If the transmitter does not illuminate when you press any buttons, or you see nothing
on the LCD screen, check the position of the batteries.
TRANSMITTER
MODE
TIME
TIMER
SET
DOWN
UP
+
+
-
-
LIQUID CRYSTAL DISPLAY - LCD
ON
OFF
THERMO
X
ROOM
SET
AM
PM
TIMER
FLAME
E
E
1
2
3
4
5
6
7
8
1. Low Battery Indicator - Battery power is low, replace batteries within two weeks.
2. Timer - Time remaining before the system shuts off.
3. Mode - Indicates whether the system is ON, OFF, or in THERMO mode.
4. Set - Indicates the desired SET temperature when in THERMO mode.
5. Flame - Indicates appliance is on.
6. Clock - Indicates current time.
7. Room - Indicates current ROOM temperature.
8. ºF - Indicates degrees Fahrenheit (ºC indicates degrees Celsius).
MODE FUNCTION
To select an operational mode, press the MODE button on the transmitter.
ON - Turns the appliance ON, the ame icon will appear on the LCD screen.
THERMO - Remote is in THERMO mode.
OFF - Turns the appliance OFF, the ame will disappear from the LCD screen.
The factory setting for temperature is degrees Fahrenheit (ºF). To change this
setting to degrees Celsius (ºC):
• Remove battery cover on the back of the transmitter and locate the setting
button in the top center of the battery compartment.
• Push the button once to enter temperature scale setting mode.
• Use the up and down buttons to switch between the ºF and ºC.
• Push the setting button again once again to set the displayed temperature
scale.
• Repeat this procedure to switch back to ºF.
SETTING ºFAHRENHEIT / ºCELSIUS SCALE
+
+
-
-
SETTING
BUTTON

Skytech Smart Batt III Specifications

General

Type	Remote Control
Battery Type	Lithium-Ion
Input Voltage	5V
Input Current	1A
Charging Port	Micro USB
Battery	Rechargeable

Summary

INTRODUCTION

TRANSMITTER

LIQUID CRYSTAL DISPLAY (LCD)

Explains the icons and indicators on the transmitter's LCD screen.

MODE FUNCTION

Details how to select the operational mode of the appliance.

SETTING TEMPERATURE SCALE

Instructions to switch between Fahrenheit (°F) and Celsius (°C) display.

THERMOSTAT FUNCTION

THERMO UPDATING FEATURE

Describes the feature that updates room temperature every two minutes.

SETTING THE CLOCK

SETTING THE COUNTDOWN TIMER

RECEIVER

INSTALLATION

WALL MOUNT

Guide for mounting the remote receiver in a wall-mounted plastic switch box.

HEARTH MOUNT

Instructions for placing the receiver on a fireplace hearth or behind the control panel.

WIRING INSTRUCTIONS

WIRING MILLIVOLT VALVES

Procedures for connecting the receiver to millivolt gas valves.

WIRING ELECTRONIC SPARK IGNITIONS

Procedures for connecting the receiver to electronic spark ignition systems.

SYSTEM CHECK

MILLIVOLT VALVES SYSTEM CHECK

Steps to verify the system's operation with millivolt valves.

SYSTEM CHECK (CONTINUED)

ELECTRONIC IGNITION SYSTEMS SYSTEM CHECK

Steps to verify the system's operation with electronic ignition systems.

LEARNING TRANSMITTER TO RECEIVER

COMMUNICATION - SAFETY

AUTO SHUT DOWN

CHILDPROOF FEATURE

BATTERY LIFE

TRANSMITTER WALL BRACKET

TROUBLE SHOOTING

LIMITED WARRANTY