What to do if I forgot my SMC Networks barricade SMCWBR14-G2 password?
If you have forgotten or lost your password, press the Reset button on the rear panel and hold it down for at least six seconds. This will restore the device to its factory default settings.
Why is my SMC Networks barricade SMCWBR14-G2 network often interrupted?
An interrupted wireless network can occur due to several reasons: * The wireless PC may be too far from the Barricade, resulting in a weak signal. Moving the PC closer might help. * Interference from devices like microwave ovens or wireless phones can disrupt the signal. Try changing the location of these devices or the Barricade. * Changing the wireless channel on the Barricade may improve stability. * Loose antenna, connectors, or cabling could also be the cause. Ensure they are firmly connected.
How to fix SMC Networks barricade SMCWBR14-G2 when I cannot connect using the web browser?
If you cannot connect to the Barricade using a web browser, check the following: * Ensure the Barricade is configured with a valid IP address, subnet mask, and default gateway. * Verify you have a valid network connection to the Barricade and that the port you are using has not been disabled. * Inspect the network cabling between the management station and the Barricade.
Why a wireless PC cannot associate with the SMC Networks Barricade?
If a wireless PC cannot associate with the Barricade, make sure that the wireless PC has the same SSID and security settings as the Barricade.
What to do if I cannot ping the SMC Networks Barricade from the attached LAN?
If you cannot ping the Barricade from the attached LAN, or vice versa, verify that the IP addresses are properly configured and that the device you are pinging from (or to) has been configured for TCP/IP.
Why SMC Networks Barricade cannot be detected by a wireless client?
If the Barricade cannot be detected by a wireless client, it could be due to the distance between the Barricade and the wireless PC being too great. Also, make sure the wireless PC has the same SSID and security settings as the Barricade.
How to fix SMC Networks Wireless Router when LAN LED is off?
If the LAN LED is off, please check the following: * Ensure that both the Barricade and the attached device are powered on. * Confirm that the cable is securely plugged into both the Barricade and the corresponding device. * Verify that the correct cable type is being used and that its length does not exceed specified limits. * Ensure that the network interface on the attached device is configured for the proper communication speed and duplex mode. * Inspect the adapter on the attached device and cable connections for any defects. Replace any defective adapter or cable if necessary.
General| Wireless Standard | 802.11g |
|---|---|
| Wireless Speed | 54 Mbps |
| Frequency Band | 2.4 GHz |
| LAN Ports | 4 |
| WAN Ports | 1 |
| Security | WEP, WPA, WPA2 |
| Firewall | NAT, SPI |
| Antenna Type | Detachable |
| Weight | 230 g |
| VPN Support | VPN Passthrough (IPSec, PPTP, L2TP) |
Covers warranty statement, exclusive remedies, liability limits, and trademarks.
Details FCC, Industry Canada, and EU compliance statements and relevant notes.
Covers UL safety compliance, power source information, and German safety instructions.
Describes the Barricade router, its key features, benefits, and applications.
Details DMZ host support, security features, and VPN pass-through capabilities.
Lists package contents, minimum system requirements, and describes hardware.
Covers connecting to LAN, power, ISP setup, desktop, and wall mounting.
Guides on TCP/IP, DHCP, manual settings, and proxy disabling for Windows.
Provides instructions for configuring network settings on Macintosh computers.
Explains accessing the interface, navigation, login, and setup wizard.
Covers wireless, internet (WAN types), LAN, and WAN settings configuration.
Details firewall, WEP, WPA/WPA2, MAC filter, and parental control.
Covers NAT, Virtual Server, Special Apps, Maintenance, System, DNS, DDNS, Routing.
Covers NAT features for sharing IP and port forwarding for applications.
Details maintenance, firmware, reset, system time, DNS, DDNS, and remote management.
Explains static routes, RIP, and routing table management.
Addresses issues with power/LAN LEDs and network ping problems.
Covers problems with web access, passwords, and wireless network stability.
Details cable specifications, wiring, and pin assignments for Ethernet.
Explains RJ-45 port connections, including straight-through and crossover wiring.
Lists IEEE standards, interfaces, dimensions, weight, and power.
Covers advanced features, internet standards, and wireless radio specs.
Details RF output power, receiver sensitivity, and operating conditions.
Provides contact details for technical support and website resources.
To Next Page
