SMC Networks Barricade SMC7904WBRA User Manual (English)

Other manuals for SMC Networks Barricade SMC7904WBRA

Questions and Answers:

M
Melissa GeorgeJul 29, 2025
Why is my SMC Networks Barricade SMC7904WBRA's wireless network often interrupted?
- R
  roachbrianJul 29, 2025
  If your wireless network is often interrupted when using your SMC Networks Wireless Router, try the following: * Move your wireless PC closer to the Barricade to improve the signal. * Adjust the angle of the antenna. * Consider potential interference from devices like microwave ovens or wireless phones. Try changing the location of these interference sources or the Barricade itself. * Change the wireless channel on the Barricade. * Ensure that the antenna, connectors, and cabling are firmly connected.
T
Tamara BaileyAug 2, 2025
How to reset the password on my SMC Networks Barricade SMC7904WBRA?
- D
  Daniel RobertsAug 2, 2025
  To restore your SMC Networks Wireless Router password, press the Reset button on the rear panel and hold it down for at least five seconds. This will restore the device to its factory default settings.
C
cantureginaAug 6, 2025
What to do if I cannot connect to my SMC Networks Wireless Router using the web browser?
- J
  James WilliamsonAug 6, 2025
  If you cannot connect to the SMC Networks Wireless Router using a web browser, ensure that the Barricade is configured with a valid IP address, subnet mask, and default gateway. Also, verify that you have a valid network connection to the Barricade and that the port you are using has not been disabled. Check the network cabling between the management station and the Barricade.
E
Eric KnightAug 11, 2025
Why can't a wireless PC associate with my SMC Networks Barricade SMC7904WBRA?
- P
  pattonjamieAug 11, 2025
  If a wireless PC cannot connect to the SMC Networks Wireless Router, ensure that the wireless PC has the same SSID and security settings as the Barricade. You need to have the same security settings on the clients and the Barricade.
C
christinafieldsAug 15, 2025
What to do if I cannot ping the SMC Networks Barricade SMC7904WBRA from the attached LAN?
- E
  Edward MccannAug 15, 2025
  If you cannot ping the Barricade from the attached LAN, first verify that the IP addresses are properly configured. For most applications, you should use the Barricade’s DHCP function to dynamically assign IP addresses to hosts on the attached LAN. However, if you manually configure IP addresses on the LAN, verify that the same network address and subnet mask are used for both the Barricade and any attached LAN devices. Also, be sure the device you want to ping (or from which you are pinging) has been configured for TCP/IP.
D
Danielle ReynoldsAug 19, 2025
Why is the Link LED off on my SMC Networks Barricade SMC7904WBRA Wireless Router?
- R
  Regina AdamsAug 19, 2025
  If the Link LED is off on your SMC Networks Wireless Router, verify that the Barricade and the attached device are powered on. Ensure that the cable is securely plugged into both the Barricade and the corresponding device. Confirm that the proper cable type is used and that its length does not exceed the specified limits. Be sure that the network interface on the attached device is configured for the proper communication speed and duplex mode. Check the adapter on the attached device and cable connections for possible defects, and replace any defective adapter or cable if necessary.
E
Emily BentonAug 23, 2025
Why is the Power LED off on my SMC Networks Wireless Router?
- M
  Michael BatesAug 25, 2025
  If the Power LED is off on your SMC Networks Wireless Router, check the connections between the Barricade, the external power supply, and the wall outlet. If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or external power supply. If you still cannot isolate the problem, then the external power supply may be defective.