Smeg WHT712EIN - User Manual

Questions and Answers

S
sarahmanningSep 9, 2025
Why too much foam forms in my Smeg WHT712EIN?
- J
  John RoseSep 9, 2025
  If your Smeg Washer is producing too much foam, it could be due to using improper detergents for the washing machine or using an excessive amount of detergent. The detergent might have been stored under improper conditions, or some meshed laundry items like tulle may foam excessively due to their texture. Ensure the detergent is placed in the correct compartment, and that the softener is not being taken early due to valve or dispenser problems.
R
Robert ManningAug 23, 2025
How to open a stuck loading door on my Smeg WHT712EIN?
- T
  Tracy BensonAug 23, 2025
  If your Smeg Washer's loading door won't open, it could be due to several reasons. The door lock might be activated because of the water level; try draining the water by running the Pump or Spin program. The machine might be heating water or in the spinning cycle, so wait until the program is complete. The child lock could be engaged, so wait a couple of minutes after the program ends for it to deactivate. Alternatively, the door might be stuck due to pressure; try pushing and pulling the door to release it.
E
Erik CruzAug 25, 2025
Why my Smeg WHT712EIN Washer does not switch to spinning step?
- J
  Jessica Jones MDAug 25, 2025
  If your Smeg Washer isn't switching to the spinning step, there might be an unbalanced load in the machine, triggering the automatic unbalanced load detection system. Also, the machine won't spin if the water hasn't drained completely, so check the filter and drain hose. Excessive foam could also be the issue, activating the automatic foam absorption system due to too much detergent; in this case, use the recommended amount of detergent.
L
lwillisAug 27, 2025
How to start Smeg Washer if program does not start after closing the door?
- R
  Regina RyanAug 27, 2025
  If your Smeg Washer programme does not start after closing the door, it might be because the Start / Pause / Cancel button was not pressed, so press the Start / Pause / Cancel button. Also, excessive loading can make it difficult to close the loading door properly, so reduce the amount of laundry and ensure the door is closed correctly.
K
kylethomasAug 27, 2025
Why is my Smeg WHT712EIN vibrating or making noise?
- T
  Timothy RiveraAug 27, 2025
  If your Smeg Washer is vibrating or making noise, several factors could be at play. The machine might be unbalanced, so try adjusting the feet to level it. A hard object might be stuck in the pump filter, requiring you to clean it. Ensure the transportation safety bolts have been removed. The laundry load could be too small, so add more items, or it could be too large, requiring you to remove some items or redistribute them evenly. Also, check that the machine isn't leaning against anything.
K
Kyle KochAug 29, 2025
Why my Smeg Washer is not filling with water?
- S
  Susan CarterAug 29, 2025
  If your Smeg Washer isn't filling with water, start by checking if the tap is turned off and turn it on. Inspect the water inlet hose for any bends and flatten it if necessary. Also, the water inlet filter might be clogged, so clean it. Ensure the loading door is properly closed as well.
C
Connie MoralesSep 18, 2025
Why Foam is overflowing from the detergent drawer of my Smeg Washer?
- E
  Elizabeth EdwardsSep 18, 2025
  If foam is overflowing from the detergent drawer of your Smeg Washer, it's likely that too much detergent is being used. Mix 1 tablespoonful of softener with ½ liter of water and pour it into the main wash compartment of the detergent drawer. Ensure you are using the appropriate amount of detergent for the program and load size.
V
vincentleeSep 18, 2025
Why Clothes smell unpleasantly after washing in my Smeg Washer?
- A
  adelgadoSep 19, 2025
  If your clothes smell unpleasantly after being washed in your Smeg Washer, it could be because odours and bacteria layers have formed on the drum due to continuous washing at lower temperatures and/or in short programmes. To prevent this, leave the detergent drawer and the loading door ajar after each washing to avoid creating a humid environment favorable for bacteria.
L
Lisa ButlerSep 7, 2025
Why my Smeg WHT712EIN Washer does not rinse well?
- D
  David ThomasSep 8, 2025
  If your Smeg Washer is not rinsing well, the amount, brand, and storage conditions of the detergent used might be inappropriate. Ensure you're using a detergent suitable for washing machines and your laundry, and store detergents properly. The detergent might also be in the wrong compartment, or the pump filter or drain hose could be clogged or folded, so check these components.
B
Bradley LopezSep 4, 2025
Why washing performance is poor and laundry turns gray in my Smeg WHT712EIN Washer?
- A
  ambersmithSep 5, 2025
  If your Smeg Washer's washing performance is poor and the laundry turns gray, it could be due to using an insufficient amount of detergent over a long period. It may also be because washing was done at low temperatures for a long time, or insufficient detergent was used with hard water. Also, using too much detergent could be the reason.

Summary

General Safety Instructions

Life and Property Safety

Safety guidelines for appliance placement, electrical safety, and proper use to prevent injuries and damage.

Childrens Safety

Instructions for safe use by children, including supervision and handling of packaging materials.

Electrical and Hot Surface Safety

Electrical Safety

Critical electrical safety measures, including grounding, cable handling, and avoiding water contact.

Hot Surface Safety

Warning about hot surfaces, specifically the door glass during high-temperature washes.

Environmental Compliance and Intended Use

Environmental Compliance

Product compliance with WEEE/RoHS directives and guidelines for waste electrical equipment recycling.

Intended Use

Specifies the appliance is for domestic use and its primary function for washing laundry.

Technical Specifications

Installation Guide

Appropriate Installation Location

Guidance on selecting a suitable, stable, and level location for the washing machine.

Removing Packaging Reinforcement

Instructions for safely removing packaging materials before installation.

Removing Transportation Locks

Step-by-step procedure to remove safety bolts to prevent damage during transit.

Connecting Utilities

Connecting Water Supply

Requirements and steps for connecting the water inlet hose correctly and safely.

Connecting the Drain Hose

How to properly attach and secure the drain hose for efficient water discharge.

Final Installation Steps

Adjusting the Feet

Method for leveling the machine using adjustable feet for stability and reduced vibration.

Electrical Connection

Essential steps for connecting the appliance to a grounded electrical outlet.

Initial Use Preparation

Pre-use checks and running a drum cleaning cycle for optimal initial operation.

Preparation for Washing

Sorting and Preparing Laundry

Advice on sorting laundry by type and preparing items for washing.

Energy Saving Tips

Recommendations for economical and efficient use of the washing machine.

Loading the Laundry

Instructions on how to correctly load laundry into the drum for effective washing.

Correct Load Capacity

Information on maximum load capacity and the impact of overloading.

Detergent and Softener Usage

Using Detergent and Softener

Guide on selecting and using detergents and softeners in the correct compartments.

Specialized Detergent and Additive Use

Liquid Detergent Usage

Specific instructions for using liquid detergents, including special adapters.

Gel and Tablet Detergent Usage

How to use gel and tablet detergents, including placement within the machine.

Using Starch and Limescale Remover

Guidelines for using starch and limescale removers for machine maintenance.

Using Bleaches

Safe procedures for using bleaching agents during the wash cycle.

Tips for Efficient Washing

Operating the Washing Machine

Control Panel Overview

Identification and explanation of all buttons and indicators on the control panel.

Programme Selection

How to choose the appropriate wash program for different types of laundry.

Wash Programmes

Descriptions of core wash cycles like Cottons, Synthetics, and Wool for various fabric types.

Additional Wash Programmes

Wash Cycle Adjustments

Temperature Selection

How to adjust and set the wash temperature for selected programs.

Spin Speed Selection

Guidance on selecting and modifying the spin speed for optimal drying.

Programme and Consumption Data

Programme and Consumption Table

A table summarizing programs, load capacities, consumption data, and auxiliary functions.

Programme Functions

Auxiliary Function Selection

How to use additional functions like Prewash, Quick Wash, and Extra Rinse.

End Time Function

Instructions for delaying the start of a wash program up to 24 hours.

Starting and Modifying Cycles

Starting the Programme

The procedure for initiating a selected wash cycle.

Loading Door Lock Status

Understanding the door locking mechanism and its indicator light.

Modifying Selections After Start

How to pause, change settings, or add/remove laundry during a running cycle.

Child Lock Feature

Explanation and operation of the Child Lock to prevent unintended changes.

Child Lock and Programme Management

Activating Child Lock

Step-by-step guide to enable the Child Lock function.

Deactivating Child Lock

Step-by-step guide to disable the Child Lock function.

Canceling a Programme

How to stop and reset a running wash program.

End of Programme and Standby

Information on program completion, the end indicator, and standby mode.

Maintenance and Cleaning Procedures

Cleaning the Detergent Drawer

Regular cleaning procedures for the detergent dispenser to prevent buildup.

Cleaning Drum and Door

Instructions for cleaning the washing drum and loading door, including recommended agents.

Cleaning Body and Control Panel

How to clean the exterior surfaces and the control panel.

Cleaning Water Intake Filters

Maintenance steps for the filters at the water inlet valves and hoses.

Water Drainage and Pump Filter Maintenance

Draining Water and Pump Filter

Procedures for draining residual water and cleaning the pump filter.

Troubleshooting Common Issues

Program Start and Selection Problems

Solutions for issues preventing the program from starting or being selected.

Water Filling Issues

Troubleshooting steps when the machine fails to fill with water.

Water Draining Problems

Solutions for the machine not draining water, including filter and hose checks.

Vibration and Noise Issues

How to resolve problems related to machine vibration and unusual noises.

Water Leakage Troubleshooting

Identifying and fixing leaks originating from the bottom of the machine.

Machine Stoppage and Water Discharge

Explanations for temporary stoppages and direct water discharge.

Loading Door Lock Issues

Reasons why the loading door may not open and how to resolve it.

Extended Washing Time

Factors that can cause washing cycles to take longer than specified.

Performance and Appearance Troubleshooting

Programme Countdown and Spinning Issues

Troubleshooting why program timers don't countdown or the machine doesn't spin.

Laundry Appearance Problems

Solutions for laundry turning gray, retaining stains, or having oily marks.

Unpleasant Odors and Fading Colors

Addressing issues with clothes smelling bad or colors fading during washing.

Detergent and Foam Troubleshooting

Rinsing and Stiffness Issues

Solutions for poor rinsing results and laundry becoming stiff.

Softener Smell and Detergent Residue

Troubleshooting lack of softener scent and detergent buildup in the drawer.

Excessive Foam Problems

Causes and solutions for excessive foam formation and overflow from the detergent drawer.

Final Wash Outcome Troubleshooting

Laundry Remaining Wet

Reasons for laundry being wet at the end of the cycle, often due to foam or unbalanced loads.

Summary

General Safety Instructions

Life and Property Safety

Safety guidelines for appliance placement, electrical safety, and proper use to prevent injuries and damage.

Childrens Safety

Instructions for safe use by children, including supervision and handling of packaging materials.

Electrical and Hot Surface Safety

Electrical Safety

Critical electrical safety measures, including grounding, cable handling, and avoiding water contact.

Hot Surface Safety

Warning about hot surfaces, specifically the door glass during high-temperature washes.

Environmental Compliance and Intended Use

Environmental Compliance

Product compliance with WEEE/RoHS directives and guidelines for waste electrical equipment recycling.

Intended Use

Specifies the appliance is for domestic use and its primary function for washing laundry.

Technical Specifications

Installation Guide

Appropriate Installation Location

Guidance on selecting a suitable, stable, and level location for the washing machine.

Removing Packaging Reinforcement

Instructions for safely removing packaging materials before installation.

Removing Transportation Locks

Step-by-step procedure to remove safety bolts to prevent damage during transit.

Connecting Utilities

Connecting Water Supply

Requirements and steps for connecting the water inlet hose correctly and safely.

Connecting the Drain Hose

How to properly attach and secure the drain hose for efficient water discharge.

Final Installation Steps

Adjusting the Feet

Method for leveling the machine using adjustable feet for stability and reduced vibration.

Electrical Connection

Essential steps for connecting the appliance to a grounded electrical outlet.

Initial Use Preparation

Pre-use checks and running a drum cleaning cycle for optimal initial operation.

Preparation for Washing

Sorting and Preparing Laundry

Advice on sorting laundry by type and preparing items for washing.

Energy Saving Tips

Recommendations for economical and efficient use of the washing machine.

Loading the Laundry

Instructions on how to correctly load laundry into the drum for effective washing.

Correct Load Capacity

Information on maximum load capacity and the impact of overloading.

Detergent and Softener Usage

Using Detergent and Softener

Guide on selecting and using detergents and softeners in the correct compartments.

Specialized Detergent and Additive Use

Liquid Detergent Usage

Specific instructions for using liquid detergents, including special adapters.

Gel and Tablet Detergent Usage

How to use gel and tablet detergents, including placement within the machine.

Using Starch and Limescale Remover

Guidelines for using starch and limescale removers for machine maintenance.

Using Bleaches

Safe procedures for using bleaching agents during the wash cycle.

Tips for Efficient Washing

Operating the Washing Machine

Control Panel Overview

Identification and explanation of all buttons and indicators on the control panel.

Programme Selection

How to choose the appropriate wash program for different types of laundry.

Wash Programmes

Descriptions of core wash cycles like Cottons, Synthetics, and Wool for various fabric types.

Additional Wash Programmes

Wash Cycle Adjustments

Temperature Selection

How to adjust and set the wash temperature for selected programs.

Spin Speed Selection

Guidance on selecting and modifying the spin speed for optimal drying.

Programme and Consumption Data

Programme and Consumption Table

A table summarizing programs, load capacities, consumption data, and auxiliary functions.

Programme Functions

Auxiliary Function Selection

How to use additional functions like Prewash, Quick Wash, and Extra Rinse.

End Time Function

Instructions for delaying the start of a wash program up to 24 hours.

Starting and Modifying Cycles

Starting the Programme

The procedure for initiating a selected wash cycle.

Loading Door Lock Status

Understanding the door locking mechanism and its indicator light.

Modifying Selections After Start

How to pause, change settings, or add/remove laundry during a running cycle.

Child Lock Feature

Explanation and operation of the Child Lock to prevent unintended changes.

Child Lock and Programme Management

Activating Child Lock

Step-by-step guide to enable the Child Lock function.

Deactivating Child Lock

Step-by-step guide to disable the Child Lock function.

Canceling a Programme

How to stop and reset a running wash program.

End of Programme and Standby

Information on program completion, the end indicator, and standby mode.

Maintenance and Cleaning Procedures

Cleaning the Detergent Drawer

Regular cleaning procedures for the detergent dispenser to prevent buildup.

Cleaning Drum and Door

Instructions for cleaning the washing drum and loading door, including recommended agents.

Cleaning Body and Control Panel

How to clean the exterior surfaces and the control panel.

Cleaning Water Intake Filters

Maintenance steps for the filters at the water inlet valves and hoses.

Water Drainage and Pump Filter Maintenance

Draining Water and Pump Filter

Procedures for draining residual water and cleaning the pump filter.

Troubleshooting Common Issues

Program Start and Selection Problems

Solutions for issues preventing the program from starting or being selected.

Water Filling Issues

Troubleshooting steps when the machine fails to fill with water.

Water Draining Problems

Solutions for the machine not draining water, including filter and hose checks.

Vibration and Noise Issues

How to resolve problems related to machine vibration and unusual noises.

Water Leakage Troubleshooting

Identifying and fixing leaks originating from the bottom of the machine.

Machine Stoppage and Water Discharge

Explanations for temporary stoppages and direct water discharge.

Loading Door Lock Issues

Reasons why the loading door may not open and how to resolve it.

Extended Washing Time

Factors that can cause washing cycles to take longer than specified.

Performance and Appearance Troubleshooting

Programme Countdown and Spinning Issues

Troubleshooting why program timers don't countdown or the machine doesn't spin.

Laundry Appearance Problems

Solutions for laundry turning gray, retaining stains, or having oily marks.

Unpleasant Odors and Fading Colors

Addressing issues with clothes smelling bad or colors fading during washing.

Detergent and Foam Troubleshooting

Rinsing and Stiffness Issues

Solutions for poor rinsing results and laundry becoming stiff.

Softener Smell and Detergent Residue

Troubleshooting lack of softener scent and detergent buildup in the drawer.

Excessive Foam Problems

Causes and solutions for excessive foam formation and overflow from the detergent drawer.

Final Wash Outcome Troubleshooting

Laundry Remaining Wet

Reasons for laundry being wet at the end of the cycle, often due to foam or unbalanced loads.

Smeg WHT712EIN Specifications

General

Brand	Smeg
Model	WHT712EIN
Category	Washer
Language	English

Related product manuals

Smeg WHT712EIN - User Manual

Table of Contents

Questions and Answers

Summary

General Safety Instructions

Life and Property Safety

Childrens Safety

Electrical and Hot Surface Safety

Electrical Safety

Hot Surface Safety

Environmental Compliance and Intended Use

Environmental Compliance

Intended Use

Technical Specifications

Installation Guide

Appropriate Installation Location

Removing Packaging Reinforcement

Removing Transportation Locks

Connecting Utilities

Connecting Water Supply

Connecting the Drain Hose

Final Installation Steps

Adjusting the Feet

Electrical Connection

Initial Use Preparation

Preparation for Washing

Sorting and Preparing Laundry

Energy Saving Tips

Loading the Laundry

Correct Load Capacity

Detergent and Softener Usage

Using Detergent and Softener

Specialized Detergent and Additive Use

Liquid Detergent Usage

Gel and Tablet Detergent Usage

Using Starch and Limescale Remover

Using Bleaches

Tips for Efficient Washing

Operating the Washing Machine

Control Panel Overview

Programme Selection

Wash Programmes

Additional Wash Programmes

Wash Cycle Adjustments

Temperature Selection

Spin Speed Selection

Programme and Consumption Data

Programme and Consumption Table

Programme Functions

Auxiliary Function Selection

End Time Function

Starting and Modifying Cycles

Starting the Programme

Loading Door Lock Status

Modifying Selections After Start

Child Lock Feature

Child Lock and Programme Management

Activating Child Lock

Deactivating Child Lock

Canceling a Programme

End of Programme and Standby

Maintenance and Cleaning Procedures

Cleaning the Detergent Drawer

Cleaning Drum and Door

Cleaning Body and Control Panel

Cleaning Water Intake Filters

Water Drainage and Pump Filter Maintenance

Draining Water and Pump Filter

Troubleshooting Common Issues

Program Start and Selection Problems

Water Filling Issues

Water Draining Problems

Vibration and Noise Issues

Water Leakage Troubleshooting

Machine Stoppage and Water Discharge

Loading Door Lock Issues

Extended Washing Time

Performance and Appearance Troubleshooting

Programme Countdown and Spinning Issues

Laundry Appearance Problems