What to do if my Smeg Washer does not drain water?
If your Smeg Washer isn't draining water, the drain hose might be clogged or twisted; try cleaning or flattening it. Another possibility is that the pump filter is clogged, so you should clean the pump filter.
What to do if Smeg WHT712LCIT program does not start?
If the program on your Smeg Washer doesn't start after closing the door, it might be because the Start / Pause / Cancel button wasn't pressed. Press the Start / Pause / Cancel button.
What to do if Smeg Washer programme cannot be started?
If a program cannot be started or selected on your Smeg Washer, it may have switched to self-protection mode due to a supply problem, such as line voltage or water pressure. To resolve this, press and hold the On / Off button for 3 seconds.
Why is my Smeg WHT712LCIT Washer vibrating and making noise?
Your Smeg Washer might be vibrating and making noise due to several reasons. The machine may be unbalanced, so adjust the feet to level it. A hard substance might have entered the pump filter, requiring you to clean it. Ensure the transportation safety bolts have been removed. The laundry quantity might be too little or too much; adjust the load accordingly. Also, check that the machine isn't leaning on anything.
Why doesn't my Smeg Washer fill with water?
If your Smeg Washer isn't filling with water, several issues could be the cause. First, check if the tap is turned on. Next, ensure the water inlet hose isn't bent. A clogged water inlet filter can also prevent water from entering, so clean the filter. Finally, make sure the loading door is completely closed.
Why is my Smeg WHT712LCIT Washer leaking water from the bottom?
If you notice water leaking from the bottom of your Smeg Washer, the water drain hose might be clogged or twisted, requiring you to clean or flatten the hose. Alternatively, the pump filter could be clogged, so cleaning the pump filter is recommended.
How to reduce excessive foam in my Smeg WHT712LCIT Washer?
Excessive foam in your Smeg Washer can be due to several factors. Ensure you're using detergents specifically designed for washing machines. You might be using too much detergent, so reduce the amount. Improperly stored detergent can also cause this issue, so store it in a closed, dry location, away from excessive heat. Certain meshed laundry items can create too much foam, so use less detergent for those. Make sure the detergent is placed in the correct compartment.
Why is there detergent residue in my Smeg Washer drawer?
Detergent residue in your Smeg Washer drawer can occur for several reasons. Ensure the detergent drawer is dry before adding detergent. The detergent itself may have gotten damp, so keep detergents stored properly in a humidity-free environment, away from excessive temperatures. Low water pressure could also be a factor, so check the water pressure. Check the holes of the detergent compartment and clean if they are clogged. Avoid mixing softener with detergent, and wash and clean the dispenser with hot water.
Why doesn't my laundry smell like softener after using my Smeg WHT712LCIT?
If your laundry doesn't smell like softener after using your Smeg Washer, it could be because the detergent was put in the wrong compartment. If detergent is put in the prewash compartment although prewash cycle is not selected, machine can take this detergent during rinsing or softener step. Wash and clean the dispenser with hot water. Put the detergent in the correct compartment. Also, ensure that detergent isn't mixed with the softener; do not mix the softener with detergent. Wash and clean the dispenser with hot water.
What to do if my Smeg WHT712LCIT stopped shortly after starting?
If your Smeg Washer stopped shortly after the program started, it might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
To Next Page
General
