What to do if my Smeg Washer does not drain water?
If your Smeg Washer isn't draining, the water drain hose might be clogged or twisted, so try cleaning or flattening it. Alternatively, the pump filter could be clogged, so clean the pump filter.
What to do if the Smeg WHT812LSIT Washer loading door cannot be opened?
If the loading door of your Smeg Washer won't open, it could be due to a few reasons: * The door lock may be activated because of the water level. Drain the water by running the Pump or Spin program. * The machine might be heating water or spinning. Wait until the program finishes. * The child lock might be engaged. Wait a couple of minutes after the program ends for the door lock to deactivate.
How to start Smeg WHT812LSIT program after closing the door?
To start a program on your Smeg Washer after closing the door, press the Start / Pause / Cancel button.
Why does my Smeg Washer vibrate so much?
Your Smeg Washer might be vibrating due to several reasons: * The machine might be unbalanced; adjust the feet to level it. * A hard substance may have entered the pump filter; clean the pump filter. * The transportation safety bolts might not be removed; remove them. * The laundry quantity might be too little; add more laundry. * The machine might be overloaded; take out some laundry or distribute the load evenly. * The machine might be leaning on something; ensure it's not.
Why is my Smeg WHT812LSIT Washer leaking water from the bottom?
If your Smeg Washer is leaking from the bottom, it could be due to a clogged or twisted water drain hose. Try cleaning or flattening the hose. Another possible cause is a clogged pump filter, so you should clean that as well.
Why does my Smeg WHT812LSIT Washer take so long to wash?
The wash cycle on your Smeg Washer might be taking longer than usual due to several reasons: 1. Low water pressure can cause the machine to wait until it has enough water, extending the wash time. 2. Low voltage can prolong the washing time to ensure proper results. 3. A low input water temperature extends the time needed to heat the water, increasing wash time. 4. The machine might be performing extra rinses or using more rinse water. 5. Excessive foam, due to too much detergent, can activate the automatic foam absorption system, lengthening the cycle.
Why is there detergent residue in my Smeg WHT812LSIT Washer detergent drawer?
Detergent residue in the drawer of your Smeg Washer can occur if: * The detergent is put in a wet drawer; dry the drawer before adding detergent. * The detergent has gotten damp; keep detergents closed in a dry environment and avoid excessive temperatures. * The water pressure is low; check the water pressure. * The detergent in the main wash compartment got wet while taking in the prewash water because the holes of the detergent compartment are blocked; check the holes and clean if they are clogged. * There is a problem with the detergent drawer valves.
Why is my laundry stiff after washing in my Smeg WHT812LSIT Washer?
Laundry can become stiff after washing in your Smeg Washer due to: * Using an insufficient amount of detergent for the water hardness. Use the appropriate amount according to the water hardness. * Putting the detergent in the wrong compartment. Ensure it's in the correct compartment. * Mixing detergent with the softener. Do not mix them, and clean the dispenser with hot water.
Why is there too much foam in my Smeg Washer?
Too much foam in your Smeg Washer can be caused by: * Using detergents that are not appropriate for washing machines. Use appropriate detergents. * Using an excessive amount of detergent. Use only a sufficient amount. * Storing detergent under improper conditions. Store it in a closed, dry location, away from excessive heat. * Washing meshed laundry like tulle, which can foam excessively due to its texture. Use less detergent for these items. * Putting detergent in the wrong compartment. Ensure it is in the correct compartment.
Why does my laundry not smell like softener after washing in my Smeg WHT812LSIT?
If your laundry doesn't smell like softener after washing in your Smeg Washer, it could be because: * Detergent was put in the prewash compartment, even though a prewash cycle wasn't selected. This can cause the machine to take the detergent during rinsing or the softener step. Put the detergent in the correct compartment and clean the dispenser with hot water. * Detergent might be mixed with the softener. Do not mix the softener with detergent. Wash and clean the dispenser with hot water.
To Next Page
General
