What to do if the Smeg WHT1114LSIT programme cannot be started?
If the programme on your Smeg Washer cannot be started or selected, the washing machine may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). Press and hold the On / Off button for 3 seconds.
How to open a Smeg WHT1114LSIT door that is locked?
If the loading door of your Smeg Washer cannot be opened, it may be because the door lock is activated due to the water level in the machine. Try draining the water by running the Pump or Spin programme. Alternatively, the machine might be heating water or in the spinning cycle, so wait until the programme completes. Also, the child lock may be engaged; wait a couple of minutes after the programme ends for deactivation.
Why won't my Smeg Washer go to the spinning step?
If your Smeg Washer isn't switching to the spinning step, there might be an unbalanced load in the machine. The automatic unbalanced load detection system might be activated due to the laundry's distribution in the drum. Also, the machine will not spin if water is not drained completely, so check the filter and the draining hose. Excessive foam might have occurred, activating the automatic foam absorption system due to too much detergent usage; use the recommended amount of detergent.
How to start the Smeg WHT1114LSIT program?
If the program does not start on your Smeg Washer after closing the door, it may be because the Start / Pause / Cancel button was not pressed. Press the Start / Pause / Cancel button.
Why is my Smeg WHT1114LSIT not filling with water?
Your Smeg Washer might not be filling with water for several reasons. First, check if the tap is turned on. Also, the water inlet hose could be bent, or the water inlet filter might be clogged. Finally, make sure that the loading door is completely closed.
Why doesn't my laundry smell like softener after using my Smeg WHT1114LSIT?
If your laundry doesn't smell like softener after using your Smeg Washer, detergent might be put in the wrong compartment. If detergent is put in the prewash compartment although prewash cycle is not selected, machine can take this detergent during rinsing or softener step. Also, detergent might be mixed with the softener. Do not mix the softener with detergent. Wash and clean the dispenser with hot water.
Why do my clothes smell bad after washing in my Smeg WHT1114LSIT Washer?
If your clothes smell unpleasant after washing in your Smeg Washer, odours and bacteria layers may have formed on the drum as a result of continuous washing at lower temperatures and/or in short programmes. Leave the detergent drawer and the loading door ajar after each washing to prevent a humid environment favorable for bacteria.
Why did the color of my clothes fade after washing in my Smeg WHT1114LSIT?
The color of clothes faded after washing in your Smeg Washer can be caused by excessive laundry in the machine. Also, the detergent in use might be damp, or a higher temperature was selected. Select the proper programme and temperature according to the type and soiling degree of the laundry.
Why did my Smeg Washer stop soon after starting?
Your Smeg Washer might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
Why are stains persisting after washing in my Smeg WHT1114LSIT?
If stains persist or laundry isn't whitened after washing in your Smeg Washer, it could be due to insufficient detergent. Ensure you're using the recommended amount. Avoid overloading the machine, and select the proper programme and temperature for the laundry. Also, ensure you're using the correct type of detergent and avoid using too much.
General| Brand | Smeg |
|---|---|
| Model Number | WHT1114LSIT |
| Capacity | 11 kg |
| Energy Efficiency Class | A |
| Spin Speed | 1400 rpm |
| Noise Level (Spinning) | 76 dB |
| Noise Level (Washing) | 52 dB |
| Color | White |
| Delay Start | Yes |
| Child Lock | Yes |
| Energy Rating | A+++ |
| Display | Digital |
To Next Page
