Why isn't the programme time counting down on my Smeg Washer?
If the programme time isn't counting down on your Smeg Washer, the timer may stop during water intake until the machine takes in adequate water. The timer may also stop during the heating step until the machine reaches the selected temperature. Also, the timer may stop during spinning step if the automatic unbalanced load detection system is activated.
What to do if my Smeg WHT1114LSIT won't drain water?
If your Smeg Washer isn't draining water, the water drain hose might be clogged or twisted, so clean or flatten the hose. Also, the pump filter could be clogged, so clean the pump filter as well.
Why doesn't my Smeg Washer rinse well?
Poor rinsing in your Smeg Washer can occur if the amount, brand, or storage conditions of the detergent are inappropriate. Use a detergent suitable for washing machines and laundry, and store detergents properly. Make sure detergent is put in the correct compartment. A clogged pump filter or a folded drain hose can also cause rinsing issues; check both.
Why are stains persisting after washing in my Smeg WHT1114LSIT?
If stains persist or laundry isn't whitened after washing in your Smeg Washer, it could be due to insufficient detergent. Ensure you're using the recommended amount. Avoid overloading the machine, and select the proper programme and temperature for the laundry. Also, ensure you're using the correct type of detergent and avoid using too much.
Why is there too much foam in my Smeg Washer?
Excessive foam in your Smeg Washer could be due to using improper detergents for the washing machine, or using an excessive amount of detergent. It may also be caused by detergent stored under improper conditions, or some meshed laundry such as tulle. Ensure the detergent is put in the correct compartment. In addition, softener may be taken early.
Why does my Smeg Washer take longer than the specified time?
The washing cycle on your Smeg Washer might take longer than expected due to several reasons. Low water pressure can cause the machine to wait until it takes in enough water. Low voltage can also prolong washing time. Additionally, a low input water temperature extends the time needed to heat the water. The machine may also increase the amount of rinse water or add an extra rinsing step. Finally, excessive foam from too much detergent can activate the automatic foam absorption system.
Why is my Smeg WHT1114LSIT Washer leaking water from the bottom?
If you notice water leaking from the bottom of your Smeg washing machine, it could be due to a clogged or twisted water drain hose. Clean or flatten the hose to resolve this issue. Additionally, a clogged pump filter could be the cause, so ensure you clean the pump filter.
How to fix a noisy or vibrating Smeg Washer?
A noisy or vibrating Smeg Washer can be caused by several factors. Ensure the machine is standing balanced by adjusting the feet. A hard substance might be in the pump filter, so clean it. Remove the transportation safety bolts if you haven't already. If the laundry quantity is too little, add more; if overloaded, take some out. Also, ensure the machine isn't leaning on anything.
Why is my Smeg WHT1114LSIT not filling with water?
Your Smeg Washer might not be filling with water for several reasons. First, check if the tap is turned on. Also, the water inlet hose could be bent, or the water inlet filter might be clogged. Finally, make sure that the loading door is completely closed.
How to start the Smeg WHT1114LSIT program?
If the program does not start on your Smeg Washer after closing the door, it may be because the Start / Pause / Cancel button was not pressed. Press the Start / Pause / Cancel button.
General| Brand | Smeg |
|---|---|
| Model Number | WHT1114LSIT |
| Capacity | 11 kg |
| Energy Efficiency Class | A |
| Spin Speed | 1400 rpm |
| Noise Level (Spinning) | 76 dB |
| Noise Level (Washing) | 52 dB |
| Color | White |
| Delay Start | Yes |
| Child Lock | Yes |
| Energy Rating | A+++ |
| Display | Digital |
To Next Page
