socomec ATyS d M User Manual (English)

Other manuals for socomec ATyS d M

Questions and Answers:

S
Stephanie ThompsonAug 4, 2025
What to do if my socomec ATyS d M Switch cannot be switched over using the handle?
- M
  michael80Aug 4, 2025
  If your socomec Switch cannot be switched over using the handle, consider the following checks: * Verify the direction of rotation of the handle: manual switchover from position 1 to position 2 is executed clockwise, and the return operation is executed anticlockwise. * Ensure that the product is not padlocked. * Use the handle extension on the ALLEN key to check that the appropriate adjustment torque is applied. * When using a single auxiliary contact, check that the length of the screws used is not greater than 20 mm.
D
David GonzalezAug 13, 2025
Why AUTOMATIC mode is not activated on my socomec ATyS d M Switch even though the cover is closed?
- B
  Brooke PhillipsAug 13, 2025
  If AUTOMATIC mode is not activated on your socomec Switch even when the cover is closed, check that the plastic pin is in place and hitting the sensor on the bottom of the cover. This pin activates the sensor, which indicates the position of the cover (open or closed).
B
briangreenAug 25, 2025
How to lock my socomec Switch?
- C
  Colleen SnyderAug 26, 2025
  To lock your socomec Switch, check the mechanical position of the changeover switch. Locking is only possible in position 0 as standard. Locking in positions 1-0-2 is possible by modifying the product in accordance with the instructions.

socomec ATyS d M Specifications

General

Brand	socomec
Model	ATyS d M
Category	Switch
Language	English

Summary

GENERAL SAFETY INSTRUCTIONS

INTRODUCTION

The ATyS family product range

Overview of the ATyS product family with different models for various applications.

The ATyS M Range Key Features

Highlights the main characteristics and benefits of the ATyS M product range.

Selection guide

A chart to help select the appropriate ATYS M model based on application and features.

QUICK START

Quick Start ATyS d M (2P)

Step-by-step guide for quickly installing and commissioning the ATyS d M (2-pole) model.

Quick Start ATyS d M (4P)

Step-by-step guide for quickly installing and commissioning the ATyS d M (4-pole) model.

ATYS D M VERSIONS

Product presentation

Describes the key components and features incorporated into the ATyS d M transfer switch.

Specifications and advantages

Outlines the technical specifications and operational advantages of the ATyS d M.

Supply types

Details the required power supply voltage and frequency for the ATyS d M operation.

OPTIONAL ACCESSORIES

Double power supply - DPS

Information on the Double Power Supply (DPS) accessory for dual network operation.

Auxiliary contacts

Information on auxiliary contact blocks for switch position monitoring and signaling.

Bridging bars

Describes bridging bars used to create common points on the outgoing side of the switch.

Voltage sensing and power supply tap

Details the tap for voltage sensing and power supply connections.

TECHNICAL DATA

Ratings

Table detailing electrical ratings, currents, and voltages for different ATyS d M models.

Short-circuit capacity

Information on the short-circuit withstand capabilities and associated fuses.

Mechanical characteristics

Details mechanical specifications like number of changeovers and connection sizes.

EMC environment

Specifies the EMC environment classification for the product.

ENVIRONMENTAL CONDITIONS

Operating Parameters

Details humidity, temperature, and altitude limits for product operation.

Humidity

Specifies the acceptable humidity levels for product operation and storage.

Temperature

Details the operating temperature range and de-rating factors.

Storage and Protection

Guidelines for product storage and its Ingress Protection (IP) ratings.

IP rating

Specifies the Ingress Protection (IP) ratings for the product in different configurations.

PRODUCT INSTALLATION

8.1. Changing the padlocking configuration

Instructions for configuring the padlocking mechanism for different positions.

8.2. Recommanded orientation

Illustrates acceptable and recommended mounting orientations for the device.

8.3. Dimensions of the single phase product

Provides dimensional drawings for the single-phase ATyS d M product.

8.4. Back plate mounted single phase product

Shows dimensions and mounting details for back plate installation of single-phase units.

8.5. Dimensions of the three phase product

Provides dimensional drawings for the three-phase ATyS d M product.

8.6. Back plate mounted three phase product

Details dimensions and mounting for back plate installation of three-phase units.

8.7. DIN rail mounted

Illustrates the procedure and considerations for mounting the device on a DIN rail.

INSTALLATION OF OPTIONAL ACCESSORIES

9.1. Auxilliary contacts

Instructions for installing auxiliary contact modules for position signaling.

9.2. Voltage sensing and power supply tap

Guide for installing the voltage sensing and power supply tap accessory.

9.3. Bridging bars 2P

Installation procedure for 2-pole bridging bars for specific current ratings.

9.4. Bridging bars 4P

Installation procedure for 4-pole bridging bars for specific current ratings.

9.5. Terminal shrouds

Instructions for fitting terminal shrouds for safety and protection.

INSTALLING WITHIN THE ATYS M ENCLOSURE

10.1. Modular plastic enclosure

Details for installing the ATyS d M within a modular plastic enclosure.

10.2. Polycarbonate enclosure

Instructions for installing the ATyS d M within a polycarbonate enclosure.

10.2.1. Wiring in a polycarbonate enclosure

Guidance on wiring the ATyS d M when installed in a polycarbonate enclosure.

10.2.2. Extension unit

Describes the use of an extension unit with the polycarbonate enclosure.

CONNECTION OF THE POWER CIRCUITS

11.1. Ratings / cross-sections table of correspondence

Table correlating cable cross-sections with product ratings for power connections.

11.2. Parallel pole set-up for a 4P device used in single phase

Table for converting three-phase ratings to single-phase parallel pole setups.

CONNECTION OF CONTROL/COMMAND CIRCUITS

12.1. Terminal connectors designation

Identifies and describes the purpose of each terminal connector for control circuits.

12.2. Auxiliary contact operating schedule

Illustrates the operating states of the auxiliary contacts for positions I, 0, and II.

OPERATION

Product Interface and Manual Mode

Overview of the product interface and manual mode operation.

13.1. Presentation of the product interface

Overview of the ATyS d M product interface, including controls and indicators.

13.2. Manual mode

Explanation of how to access and operate the device in manual mode.

Commissioning and Automatic Mode

Steps for commissioning and operating in automatic mode.

13.4. Commissioning / Putting into service

Steps for putting the device into service.

13.5. Automatic (remote) mode

Details on how to operate the ATyS d M in automatic mode via remote control.

Control Logic

Explains the impulse and contactor logic for controlling the transfer switch.

13.6.1. Control logic

Explains the impulse and contactor logic for controlling the transfer switch.

13.6.2. Positions that can be reached depending on the available source

Table showing achievable switch positions based on source availability and DPS.

PREVENTATIVE MAINTENANCE

Maintenance Recommendations

Guidelines for performing preventative maintenance on the ATyS d M.

TROUBLESHOOTING GUIDE

15.1. Fault finding

Initial steps to identify and diagnose faults when the product does not respond.

15.2. Troubleshooting

A table detailing common symptoms, actions, and expected results for troubleshooting.

Related product manuals

socomec ATyS d 250 A

52 pages

socomec ATyS d M 160 A

socomec ATyS d M User Manual

Table of Contents

Other manuals for socomec ATyS d M

Questions and Answers:

socomec ATyS d M Specifications

Summary

GENERAL SAFETY INSTRUCTIONS

INTRODUCTION

The ATyS family product range

The ATyS M Range Key Features

Selection guide

QUICK START

Quick Start ATyS d M (2P)

Quick Start ATyS d M (4P)

ATYS D M VERSIONS

Product presentation

Specifications and advantages

Supply types

OPTIONAL ACCESSORIES

Double power supply - DPS

Auxiliary contacts

Bridging bars

Voltage sensing and power supply tap

TECHNICAL DATA

Ratings

Short-circuit capacity

Mechanical characteristics

EMC environment

ENVIRONMENTAL CONDITIONS

Operating Parameters

Humidity

Temperature

Storage and Protection

IP rating

PRODUCT INSTALLATION

8.1. Changing the padlocking configuration

8.2. Recommanded orientation

8.3. Dimensions of the single phase product

8.4. Back plate mounted single phase product

8.5. Dimensions of the three phase product

8.6. Back plate mounted three phase product

8.7. DIN rail mounted

INSTALLATION OF OPTIONAL ACCESSORIES

9.1. Auxilliary contacts

9.2. Voltage sensing and power supply tap

9.3. Bridging bars 2P

9.4. Bridging bars 4P

9.5. Terminal shrouds

INSTALLING WITHIN THE ATYS M ENCLOSURE

10.1. Modular plastic enclosure

10.2. Polycarbonate enclosure

10.2.1. Wiring in a polycarbonate enclosure

10.2.2. Extension unit

CONNECTION OF THE POWER CIRCUITS

11.1. Ratings / cross-sections table of correspondence

11.2. Parallel pole set-up for a 4P device used in single phase

CONNECTION OF CONTROL/COMMAND CIRCUITS

12.1. Terminal connectors designation

12.2. Auxiliary contact operating schedule

OPERATION

Product Interface and Manual Mode

13.1. Presentation of the product interface

13.2. Manual mode

Commissioning and Automatic Mode

13.4. Commissioning / Putting into service

13.5. Automatic (remote) mode

Control Logic

13.6.1. Control logic

13.6.2. Positions that can be reached depending on the available source

PREVENTATIVE MAINTENANCE

Maintenance Recommendations

TROUBLESHOOTING GUIDE

15.1. Fault finding

15.2. Troubleshooting

Related product manuals