What to do if Sofar solar HYD 6KTL-3PH Inverter AC frequency is too high?
If the AC frequency of your Sofar solar Inverter is too high, please ensure the grid frequency and voltage are within the acceptable range.
What to do if Sofar solar HYD 6KTL-3PH displays GFCI error?
If your Sofar solar inverter displays a GFCI error, switch OFF the inverter, wait for 5 minutes, and then switch it ON again to see if the problem is resolved. If the error persists, it may indicate internal faults of the inverter, and you should contact technical support for further assistance.
What to do if Sofar solar HYD 6KTL-3PH Inverter displays TempFault_Bat error?
If your Sofar solar inverter displays a TempFault_Bat error, ensure that the battery NTC cable is properly connected for Inner BMS battery. Also, make sure the inverter is installed where there is no direct sunlight, in a cool and well-ventilated place. Ensure the inverter is installed vertically and the ambient temperature is below the inverter temperature limit.
Why Sofar solar Inverter shows OverTempDerating?
The OverTempDerating error on your Sofar solar inverter indicates it's overheating. To resolve this, ensure the inverter is installed in a cool, well-ventilated area away from direct sunlight. Also, verify that the inverter is mounted vertically and that the ambient temperature is below the inverter's temperature limit.
What to do if Sofar solar HYD 6KTL-3PH Inverter displays 'Battery low voltage protection'?
If your Sofar solar Inverter shows a 'Battery low voltage protection' message, check whether the battery voltage of the inverter is too low.
What to do if Sofar solar HYD 6KTL-3PH displays 'Master does not exist or is duplicate'?
If your Sofar solar Inverter shows 'Master does not exist or is duplicate', check the parallel mode settings for the inverter and ensure the wiring is correct.
How to fix PvConfigError on Sofar solar HYD 6KTL-3PH?
To fix a PvConfigError on your Sofar solar Inverter, check the PV input mode (parallel/independent mode) settings for the inverter and change the PV input mode if needed.
What to do if Sofar solar HYD 6KTL-3PH shows grid overvoltage?
If your Sofar solar Inverter is showing a grid overvoltage error occasionally, it might be due to temporary grid issues; the inverter should return to normal when the grid stabilizes. However, if this happens frequently, verify that the grid voltage/frequency is within the acceptable range. If it is, inspect the AC circuit breaker and AC wiring of the inverter. If the grid voltage/frequency is outside the acceptable range and the AC wiring is correct, and the alarm persists, you may need to contact technical support to adjust the grid over-voltage, under-voltage, over-frequency, under-frequency protection points, but only after getting approval from your local electrical grid operator.
Why does my Sofar solar HYD 6KTL-3PH Inverter show a BMSCommunicationFault?
A BMSCommunicationFault on your Sofar solar inverter may occur if your battery is not compatible with the inverter. CAN communication is recommended. Check the communication line or port of the battery and inverter for faults.
What causes PVOVP error on Sofar solar Inverter and how to fix it?
The PVOVP error on your Sofar solar inverter indicates that the PV series voltage (Voc) is higher than the maximum input voltage of the inverter. To resolve this, check whether the PV series voltage is indeed too high. If it is, adjust the number of PV modules in series to reduce the PV series voltage, ensuring it fits within the input voltage range of the inverter. After making this correction, the inverter should automatically return to its normal state.
Details essential safety precautions and guidelines for operating the inverter.
Specifies requirements for personnel authorized to install and maintain the inverter.
Provides a step-by-step guide for the inverter installation procedure.
Details how to connect the battery and PV modules to the inverter.
Guides on connecting the AC load to the inverter.
Explains how to connect the inverter to the AC grid.
Lists checks to perform before operating or commissioning the inverter.
Provides critical steps for the initial setup and power-on procedure.
Details wiring and configuration for a single battery pack connection.
General| Rated Output Power | 6000 W |
|---|---|
| Max. DC Input Power | 9000 W |
| Number of MPPTs | 2 |
| Nominal AC Output Power | 6000 W |
| Max. AC Output Power | 6600 VA |
| Nominal Grid Frequency | 50 Hz / 60 Hz |
| THDI | <3% |
| Max Efficiency | 98.4% |
| DC Switch | Yes |
| Protection Degree | IP65 |
| Operating Temperature Range | -25°C to +60°C |
| Cooling | Natural Convection |
| Nominal AC Voltage | 230V / 400V |
| AC Voltage Range | 310 V - 480 V |
| Power Factor | 0.8 leading to 0.8 lagging |
| Communication | RS485, Wi-Fi |
To Next Page