SolarEdge SE4000 - User Manual

Questions and Answers:

J
James Douglas IIIAug 14, 2025
What to do if my SolarEdge SE4000 has an Ethernet communication error?
- J
  Julie ClarkAug 14, 2025
  If you're experiencing an Ethernet communication error with your SolarEdge Inverter, begin by ensuring the Ethernet cable is properly connected, paying attention to the cable pin-out assignment. Also, verify that the DHCP IP is configured correctly by checking both the router and inverter configurations. If the internet connection is not operating, this may also cause the error. Communication issues with the SolarEdge server can be resolved by checking the server address.
T
tara04Aug 17, 2025
How to fix DHCP Failed or Invalid DHCP Config on SolarEdge SE4000?
- R
  Regina HopkinsAug 17, 2025
  If your SolarEdge Inverter shows 'DHCP Failed' or 'Invalid DHCP Config', it indicates an issue with the IP settings. To resolve this, check both the router and inverter configurations.
M
Mr. Shawn Nelson MDAug 21, 2025
How to fix LAN Disconnected on SolarEdge SE4000 Inverter?
- C
  Christina HartmanAug 21, 2025
  If your SolarEdge Inverter shows 'LAN Disconnected', it indicates a fault with the physical connection. Check the cable pin-out assignment and cable connection.
D
Denise HallAug 25, 2025
What to do if string voltage is lower than number of optimizers in SolarEdge SE4000 Inverter?
- M
  Matthew RussellAug 26, 2025
  If the string voltage of your SolarEdge Inverter is not 0V but lower than the number of optimizers, it could be due to several reasons. First, ensure all power optimizers are properly connected in the string. Second, verify that all modules are correctly connected to the power optimizer inputs. Lastly, check the string polarity using a voltmeter and correct it if necessary.
A
anthonydouglasAug 29, 2025
Why is string voltage higher than number of optimizers in SolarEdge SE4000 Inverter?
- B
  Benjamin TranAug 29, 2025
  If the string voltage of your SolarEdge Inverter is higher than the number of optimizers, there could be a few reasons. First, check if an extra power optimizer is connected in the string. Next, verify that only power optimizers are connected in the string and that no module outputs are connected without a power optimizer. If the issue persists, follow these steps: 1. Disconnect the wires connecting the power optimizers in the string. 2. Measure the output voltage of each power optimizer to locate any that aren't outputting the 1V safety voltage. Check the connections, polarity, module, and voltage of any malfunctioning power optimizers.
M
Michael FieldsSep 1, 2025
What to do if Gateway Ping Failed on SolarEdge Inverter?
- J
  Jordan HicksSep 1, 2025
  If your SolarEdge Inverter shows 'Gateway Ping Failed', the ping to the router has failed. Check the physical connection to the switch or router and ensure the link LED at the router or switch is lit, indicating a physical link. If the connection is fine, replace the cable or change it from cross to straight connection.
L
Lance ThomasSep 5, 2025
How to fix String voltage is 0V on SolarEdge SE4000 Inverter?
- A
  Autumn BrownSep 5, 2025
  If the string voltage is 0V on your SolarEdge Inverter, it means a power optimizer output is disconnected. To fix this, connect all power optimizer outputs.
W
wmartinezSep 9, 2025
What to do if G Server Ping Failed on SolarEdge SE4000 Inverter?
- S
  Sylvia GreenSep 9, 2025
  If your SolarEdge Inverter displays 'G Server Ping Failed', it indicates that the ping to google.com has failed. To resolve this, connect a laptop and check for internet connectivity.

SolarEdge SE4000 Specifications

General

Model	SE4000
Manufacturer	SolarEdge
Rated AC Power	4000 W
CEC Weighted Efficiency	97.5%
Number of MPP Trackers	1
Protection Rating	IP65
Cooling	Natural Convection
Warranty	12 years
AC Output Power	4000 W
AC Voltage	220 / 230 / 240 Vac
Max. DC Input Power	5400 W
Operating Temperature Range	-25°C to 60°C