SolarEdge SE3000 User Manual (English)

Questions and Answers:

J
jessica28Aug 13, 2025
What to do if my SolarEdge SE3000 Inverter has an Ethernet communication error?
- L
  landrymatthewAug 13, 2025
  If you're experiencing an Ethernet communication error with your SolarEdge Inverter, begin by ensuring the Ethernet cable is properly connected, paying attention to the cable pin-out assignment. Also, verify that the DHCP IP is configured correctly by checking both the router and inverter configurations. If the internet connection is not operating, this may also cause the error. Communication issues with the SolarEdge server can be resolved by checking the server address.
K
kennedyjamesAug 17, 2025
How to fix DHCP Failed or Invalid DHCP Config on SolarEdge SE3000?
- J
  jwoodAug 17, 2025
  If your SolarEdge Inverter shows 'DHCP Failed' or 'Invalid DHCP Config', it indicates an issue with the IP settings. To resolve this, check both the router and inverter configurations.
M
Mr. Don MurphyAug 20, 2025
How to fix LAN Disconnected on SolarEdge SE3000?
- J
  johnstonryanAug 20, 2025
  If your SolarEdge Inverter shows 'LAN Disconnected', it indicates a fault with the physical connection. Check the cable pin-out assignment and cable connection.
D
Danielle CaseAug 25, 2025
What to do if string voltage is lower than number of optimizers in SolarEdge Inverter?
- P
  Paula CollinsAug 25, 2025
  If the string voltage of your SolarEdge Inverter is not 0V but lower than the number of optimizers, it could be due to several reasons. First, ensure all power optimizers are properly connected in the string. Second, verify that all modules are correctly connected to the power optimizer inputs. Lastly, check the string polarity using a voltmeter and correct it if necessary.
F
Fred FuentesAug 28, 2025
Why is string voltage higher than number of optimizers in SolarEdge Inverter?
- J
  Jessica JonesAug 28, 2025
  If the string voltage of your SolarEdge Inverter is higher than the number of optimizers, there could be a few reasons. First, check if an extra power optimizer is connected in the string. Next, verify that only power optimizers are connected in the string and that no module outputs are connected without a power optimizer. If the issue persists, follow these steps: 1. Disconnect the wires connecting the power optimizers in the string. 2. Measure the output voltage of each power optimizer to locate any that aren't outputting the 1V safety voltage. Check the connections, polarity, module, and voltage of any malfunctioning power optimizers.
S
Scott SmithSep 1, 2025
What to do if Gateway Ping Failed on SolarEdge SE3000?
- M
  Mrs. Lisa JenningsSep 1, 2025
  If your SolarEdge Inverter shows 'Gateway Ping Failed', the ping to the router has failed. Check the physical connection to the switch or router and ensure the link LED at the router or switch is lit, indicating a physical link. If the connection is fine, replace the cable or change it from cross to straight connection.
J
Jorge RussellSep 5, 2025
How to fix String voltage is 0V on SolarEdge SE3000 Inverter?
- M
  Megan JacobsSep 5, 2025
  If the string voltage is 0V on your SolarEdge Inverter, it means a power optimizer output is disconnected. To fix this, connect all power optimizer outputs.
M
Martha OchoaSep 8, 2025
What to do if G Server Ping Failed on SolarEdge Inverter?
- B
  Brianna PowellSep 8, 2025
  If your SolarEdge Inverter displays 'G Server Ping Failed', it indicates that the ping to google.com has failed. To resolve this, connect a laptop and check for internet connectivity.

SolarEdge SE3000 Specifications

General

Model	SE3000
Manufacturer	SolarEdge
AC Output Power	3000 W
Cooling	Natural Convection
Protection Rating	IP65
Rated AC Power	3000 W
Max. AC Power	3000 VA
Maximum Output Current	13 A
Number of MPP Trackers	1
Operating Temperature Range	-25°C to 60°C
AC Voltage	230 V
Max. Input DC Voltage	480 V