SOMFY Soliris User Manual

The SOLIRIS receiver RTS is a radio receiver for awnings with an auto-
matic control according to the daylight intensity and protection against
wind damage.
The SOLIRIS receiver RTS has to be used with the TELIS soliris RTS and
the SOLIRIS sensor.
The SOLIRIS receiver RTS is also compatible with the other RTS controls
and the INIS RT (the functioning is a trip switch type : ▲, stop, ▼, stop,…)
Commands are transmitted by radio (frequency 433.42 MHz).
®
❏ Mains supply : 220-240 V~ 50/60 Hz
❏ Protection index: IP 44
❏ Operating temperature: -20°C to +50°C
❏ Class II product once installed
❏ Normally polluted environment
inteo SOLIRIS receiver RTS
INSTALLATION guide
Ref.182249A
Characteristics:
Installation:
2
108 mm
108 mm
Before connecting the unit, you must read the instructions carefully.
NNL
▲
▼
SC
MAIN
SUPPLY
Earth
Phase
Neutral
Soliris receiver RTS
LT motor
N
Soliris sensor
SC
SC
= Main phase
= Main neutral
= Motor neutral
= Motor up
= Motor down
= SUN input
= WIND input
= COMMON input
N
N
L
▲
▼
58 mm
150 mm
1
Mounting of the SOLIRIS receiver RTS :
A
The SOLIRIS receiver RTS is compatible with all standard SOMFY
motors. Cabling arrangements are shown in the diagram.
Respect the electrical standards in force as well as the following points:
❏disconnect the mains before carrying out any work.
❏ Install the SOLIRIS receiver RTS with the cables entry pointing downwards
to avoid water infiltration.
❏ Do no install the SOLIRIS receiver RTS against a metallic part
(it could affect the radio transmission).
❏ minimum distance between the receiver and the floor : 1,5 m.
❏ minimum distance between the receiver and the roof : 30 cm.
❏ minimum distance between the receiver and the transmitter : 30 cm.
❏ minimum distance between two receivers : 20 cm.
wind led
prog button
prog led
sun led
wind
potentiometer
sun
potentiometer
manual
control button

SOMFY Soliris Specifications

General

Brand	SOMFY
Model	Soliris
Category	Receiver
Language	English

Summary

Mounting the SOLIRIS Receiver RTS

Initial Installation and Programming

Programming with RTS Controls

Guide for setting up the SOLIRIS receiver with TELIS, Centralis, or other RTS controls for initial installation.

Multiple Control Setup

Instructions for assigning multiple RTS controls to a single SOLIRIS receiver, up to 16 controls.

Programming with INIS RT

Procedure for programming a single INIS RT control into the SOLIRIS receiver's memory.

General or Group Control

Steps to set multiple SOLIRIS receivers for control by a single RTS control.

Add New Control to Receiver Memory

Procedure to add a new RTS control to a receiver already programmed.

Removing Controls and Intermediate Positions

Remove a Single RTS Control

Procedure to remove a specific RTS control from the SOLIRIS receiver's memory.

Remove All Controls (Reset)

Instructions for clearing all programmed controls from the SOLIRIS receiver memory.

Set Intermediate Positions

Guide to record top (IP1) and bottom (IP2) intermediate awning positions.

Reach Intermediate Positions

Manual and automatic methods to reach recorded intermediate awning positions.

Delete Intermediate Position

Steps to remove a previously recorded intermediate awning position.

Wind and Sun Functionality

Sun Function

Details on how the receiver reacts to daylight intensity for awning control.

Wind Function

Explanation of the receiver's response to wind speed for awning protection.

Installation/Commissioning Mode

Information on the mode that reduces delay times for easier installation.

Troubleshooting Diagnosis

Common issues and checks for RTS control and motor operation problems.