59
CDX-5V661/5V661A/5V661D/5V661S
Pin No. Pin Name I/O Description
90 NC O Not used (open)
91
EMR O Elevator motor drive (negative) signal output to the LB1836M (IC502)
92
EM O Elevator motor drive (positive) signal output to the LB1836M (IC502)
93
CM O Chucking motor drive (positive) signal output to the LB1836M (IC502)
94
CMR O Chucking motor drive (negative) signal output to the LB1836M (IC502)
95
LM O Loading motor drive (positive) signal output to the LB1930M (IC501)
96
LMR O Loading motor drive (negative) signal output to the LB1930M (IC501)
97 PANASO
O PANA bus status data output terminal
98
NC O Not used (open)
99 GND —
Ground terminal
100 GND —
Ground terminal
101 PANACKO O
Clock output terminal for PANA bus status data
102 NC O
Not used (open)
103 AVCC —
Analog power supply terminal (+3.3V) (for A/D, D/A converter)
104 VREF I
Analog reference voltage (+3.8V) input terminal (for A/D, D/A converter)
105 TEMP I
Temperature detect signal input terminal (A/D input)
106 BU CHK I
Back-up voltage detect signal input terminal (A/D input)
107 MDP I
Spindle motor speed control signal input from the CXD3027R (IC601)
108 PULLDOWN —
For pulldown terminal (fixed at “L” in this set)
109 DIMMER IN I
Dimmer signal input terminal (A/D input)
110 DCP I
Elevator height position detect input from the RV1 (elevator height sensor) (A/D input)
111 PULLDOWN I
For pulldown terminal (fixed at “L” in this set)
112 PULLDOWN I
For pulldown terminal (fixed at “L” in this set)
113 AGND —
Ground terminal (analog)
114 GND —
Ground terminal
115 NC I
Not used (fixed at “L” in this set)
116 LIGHT O
Dimmer signal output for the indicator LED
117 NC I
Not used (fixed at “L” in this set)
118 DIMMER O
Dimmer signal output for the key LED
119 NC O
Not used (open)
120 DIN L I
Disc in detect signal (left) input terminal
121 DIN R I
Disc in detect signal (right) input terminal
122 R SI I
PANA bus command signal input from the TC7SH14FU (IC870)
123 MD0 I
Setting terminal for the CPU operation mode (fixed at “H” in this set)
124 MD1 I
Setting terminal for the CPU operation mode (fixed at “H” in this set)
125 MD2 I
Setting terminal for the CPU operation mode (fixed at “H” in this set)
126 NC O
Not used (open)
127
K1
I
Key input terminal S1, S2 (1)
128
K2 I Key input terminal S3, S4 (2)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page