Sony ICF-2001D - Tuning Operation Details; Direct Frequency Input Methods; Manual Tuning Procedures

ICF-2001D/2010
To
input
a
frequency
whose
righthand
digits
are
all
0
1
Set
the
MAIN
POWER
switch
and
the
POWER
switch
to
ON.
2
Select
the
desired
band.
AM
2,000
kHz
For
AM
reception,
select
the
required
AM
mode.
=
(See
“How
to
select
AM
mode”
on
page
11,)
a)
Fy
[EXECUTE]
aan)
3
Set
the
MANUAL
TUNE
MODE
selector
to
SLOW
or
FAST.
oT
ie
laos
ES,
4
Turn
the
MANUAL
TUNING
knob
to
tune
in
a
desired
station
so
FM
90.0
MHz
Bay
Yoh
that
more
LEDs
of
the
SIGNAL
STRENGTH indicator
light.
ie
7
For
lower
For
higher
e)
g
GE
Bae
frequencies
=
frequencies
L
Mw
SAME
-
° ae J 2 Fu g 2 S fn me ods
In
case
of
10,000kHz
and
20,000
kHz,
however,
press
[4]
[0]
ie
ae
(EXECUTE) and (2] (0) [EXECUTE], respectively.
In case of 200 kHz, 300 kHz, ... 900 kHz, press (2) o) {0} [EXECUTE] ;
(3) [0] [0} (EXECUTE), etc.
@
After
pressing
a
key,
press
the
next
key
within
5
seconds.
If
you
do
not,
the
previous
station
will
return.
As the MANUAL TUNING knob is turned, the frequency is tuned
in and displayed at the following intervals, depending on the
@With
direct
tuning,
the
frequency
is
displayed
in
steps
of
the
bands.
:
following intervals, depending on the bands. AM: 0.1 kHz (with the MANUAL TUNE MODE selector set to SLOW)
AM:
1
kHz
1
kHz
(with
the
MANUAL
TUNE
MODE
selector
set
to
FAST)
FM: 0.05 MHz FM: 0.05 MHz
AIR: 0.025 MHz AIR: 0.025 MHz
5 Adjust the antenna. See page 11.
If
you
input
a
frequency
between
the
intervals,
the
frequency
at
the
°
Y
q
y
6
Adjust
the
volume
with
the
VOLUME
control.
interval
just
below
will
be
tuned
in
and
displayed.
For
example,
if
you
input
FM
92.540
MHz,
FM
92.500
MHz
will
be
tuned
in
an
displayed.
eng
After
listening,
set
the
POWER
switch
to
OFF.
Error indication
t
Error.
Note
When the upper or lower limit of the band frequency is reached, the
frequency no longer changes even if the MANUAL TUNING knob is
turned further.
How to use the MANUAL TUNE MODE selector
The manual tuning interval of AM frequency can be set with the
MANUAL TUNE MODE selector, to 0.1 kHz (at SLOW position) or
1 kHz (at FAST position).
After tuning in a station with the selector set to FAST, tune it in
more precisely, setting the selector to SLOW. Once the frequency
of any band is precisely tuned, set the selector to LOCK. The fre-
quency no longer changes even if the MANUAL TUNING knob is ac-
cidentally turned.
When you input a frequency beyond the receivable frequency
range, this indication will blink several times and the previous
Station will return. = Input a correct frequency.
Errors
If you set the POWER switch to ON or press the SLEEP key when
there is no radio power source, this indication will appear for ap-
prox. 5 seconds and then disappear.
™ Check the following.
@The MAIN POWER switch is set to OFF. MANUAL
@The radio batteries are exhausted. TUNE MODE
@The ac power adaptor or the car battery cord is connected to TUNE
the DC iN 4.5 V jack when battery operation is attempted. AM |
@ The ac power adaptor or the car battery cord is not connected cc owe
correctly to a wall outlet or a cigarrette lighter socket of a car.
MANUAL
TUNING
‘al
Use manual tuning when you do not know the frequency of the sta- Note ae
tion you want to tune in, or when you want to tune in a station more FO’ AM (LW, MW and SW) reception in SYNC, USB or LSB/CW
mode, be sure to set this selector to SLOW.
precisely after scan tuning.
The numbers in the illustration refer to the sequence of operations.