Sony STR-V200 - Specifications

18
Additional Information
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 8 ohm loads, both
channels driven, from 20 -
20,000 Hz; rated 50 watts
per channel minimum RMS
power, with no more than
0.09% total harmonic
distortion from 250
milliwatts to rated output.
Amplifier section
POWER OUTPUT
Stereo mode (8 ohms 20 Hz - 20 kHz,
THD 0.09%)
50 W + 50 W
Surround mode (8 ohms at 1 kHz, THD
0.8%)
Front: 50 W/ch
Center*: 50 W
Rear*: 50 W/ch
* Depending on the
surround mode and the
source, sound will not be
output.
Frequency response
CD, TAPE/MD, TV/DBS,
VIDEO:
10 Hz - 50 kHz ±1 dB
Inputs
Impedance
S/N
(weighting
network,
input level)
Sensitivity
82 dB
(A, 150
mV)
50 kilohms
150 mV
TAPE/MD,
TV/DBS,
VIDEO
CD
200 mV
Outputs TAPE/MD REC OUT:
Voltage: 150 mV,
Impedance: 10 kilohms
VIDEO AUDIO OUT:
Voltage: 150 mV,
Impedance: 10 kilohms
MIX AUDIO OUT:
Voltage: 2 V
Impedance: 10 kilohms
PHONES:
Accepts low and high
impedance headphones
MUTING Full mute
BASS BOOST +10 dB at 70 Hz
TONE ±8 dB at 100 Hz and 10 kHz
FM tuner section
Tuning range 87.5 - 108.0 MHz
Antenna terminals
300 ohms, balanced
75 ohms, unbalanced
Sensitivity Mono: 18.3 dBf, 4.5 µV
Stereo: 38.3 dBf, 45 µV
Usable sensitivity
11.2 dBf, 2 µV (IHF)
S/N Mono: 0.3%
Stereo: 0.5%
Harmonic distortion at 1 kHz
0.5%
Separation 45 dB at 1 kHz
Frequency response
30 Hz - 15 kHz
–2
+0.5
dB
Selectivity 60 dB at 400 kHz
AM tuner section
Tuning range With 10 kHz interval: 530 -
1710 kHz**
Antenna Loop antenna
Usable sensitivity
50 dB/m (at 1,000 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion
0.5% (50 mV/m,
400 Hz)
Selectivity At 10 kHz: 40 dB
** You can change the AM tuning
interval to 9 kHz or to 10 kHz. After
tuning in any AM station, turn off
the receiver. Hold down the
TUNING + button and press the 1/u
button. All preset stations will be
erased when you change the interval.
To reset the interval to 10 kHz, repeat
the procedure.
General
System Tuner section:
PLL quartz-locked digital
synthesizer system
Preamplifier section:
Low-noise NF type
equalizer
Power amplifier section:
Pure-complementary
SEPP
Power requirements
120 V AC, 60 Hz
Power consumption
150 W
AC outlets 1 switched, 120 W/1 A
maximum
Dimensions 355 × 120 × 325 mm
(14 × 4
3
/4 × 12
3
/4 inches)
including projecting parts
and controls
Mass (Approx.)
5.9 kg (13 lb)
Supplied accessories
See page 4.
Design and specifications are subject to
change without notice.