— 12 —
KV-32FS10/32FV15/32XBR250/34FV10/34FV15/34FV15C/34FX250C/34FV15K
34FV15T/36FS10/36FV15/36XBR250/38FX250/38FX250C/38FX250T/38FV15K
30
Laserdisc
code numbers
Manufacturer Code
Sony 701
Panasonic 704, 710
Pioneer 702
Operating a
Laserdisc
To turn on or off
To play
To stop
To pause
To scan
To search the
chapter forward or
backward
Tip z
If you will not be programming a satellite receiver or
cable box into the SAT/CABLE function of your remote,
you can use it to program other video equipment (e.g.
DVD, MDP, or second VCR).
DVD (Digital Versatile Disc)
code numbers
Manufacturer Code
Sony 751
Panasonic 753
Pioneer 752
RCA 755
Toshiba 754
Operating a DVD
player
To turn on or off
To play
To stop
To pause
To scan
To search the
chapter forward or
backward
To select chapters
directly
MENU
To move cursor in
menu
Buttons on the remote
control
Press VTR/DVD (POWER).
Press (.
Press p.
Press P.
To resume normal playback,
press again or press (.
Press ) or 0 during
playback.
To resume normal playback,
press (.
Press CH +/–.
0-9 + ENTER.
Press to display DVD menu.
Use your arrow buttons
V, v, B, b.
Buttons on the remote
control
Press VTR/DVD (POWER).
Press (.
Press p.
Press P.
To resume normal playback,
press again or press (.
Press ) or 0 during
playback.
To resume normal playback,
press (.
Press CH +/–.
Tips z
• In some rare cases, you may not be able to operate
your non-Sony video equipment with the supplied
remote control. In this case, please use the
equipment’s own remote control.
• When you remove the batteries, the code number may
revert to the factory setting.
• The code numbers for Sony VCRs are assigned at the
factory as follows:
VHS VCR 301
(preset code for the
supplied remote control)
8 mm VCR 302
Beta, ED Beta VCRs 303
Operating Video Equipment (continued)
31
Manufacturer
Hamlin/Regal
Jerrold/G. I.
Oak
Panasonic
Pioneer
Scientific Atlanta
Tocom
Zenith
Programming the remote
control
You can program the supplied remote
control to operate a cable box or satellite
receiver.
1
Press CODE SET.
2
Press SAT/CABLE (FUNCTION).
3
Use the 0-9 buttons to key in the
manufacturer's code number from the
following chart.
4
Press ENTER.
For more details on operating the
cable box or satellite receiver
Refer to the operating instructions that were
supplied with the equipment.
If the remote control doesn’t work
First, try repeating the setup procedures
using the other codes listed for your
equipment.
Tips z
• If more than one code number is listed, try
entering them one by one until you come to the
correct code for your equipment.
• If you enter a new code number, the code number
you previously entered at that setting is erased.
• In some rare cases, you may not be able to operate
your equipment with the supplied remote control.
In this case, use the equipment’s supplied remote
control.
• Whenever you remove the batteries the code
numbers may revert to the factory setting.
Cable box code numbers
Code
222, 223, 224, 225, 226
201, 202, 203, 204, 205, 206,
207, 208, 218
227, 228, 229
219, 220, 221
214, 215
209, 210, 211
216, 217
212, 213
Satellite receiver code numbers
Manufacturer
Sony
General Electric
Hitachi
Hughes
Panasonic
RCA/PROSCAN
Toshiba
Code
801 (preset code for
remote control)
802
805
804
803
802, 808
806, 807
Operating a Cable Box or Satellite Receiver
28
PARENTAL LOCK
Turns ratings on/off
RATING
CHANGE
PASSWORD
Setting the TV’s RATING
This section provides information on how to
set the TV’s RATING and how to change
your password.
Note
Entering your password to view a blocked
program will temporarily turn PARENTAL
LOCK to OFF. To reactivate your
PARENTAL CONTROL settings, turn the TV
off then back on; the TV will restore your
rating settings.
ON: Select to activate the RATING.
OFF: Turns off current ratings.
If you are not familiar with the Parental Guideline rating system, you should use
one of the following preselected categories to help simplify the rating selection.
The following maximum ratings will be allowed:
CHILD: TV-Y, TV-G, G (U.S. models only),
TV-Y, G (Canadian models only).
YOUTH: TV-PG, PG (U.S. models only),
TV-PG, PG, 8 ans+ (Canadian models only).
YOUNG ADULT: TV-14, PG-13 (U.S. models only),
TV-14, 14+, 13 ans+ (Canadian models only).
CUSTOM: If you prefer to set more restrictive ratings, highlight CUSTOM and
press
. See pages 25-26, for an overview of the rating systems available.
In the CUSTOM RATINGS menu:
1 Select the desired rating category and press
.
2 Press V or v to select the maximum rating or content and press
.
3 Press V or v to block or unblock the rating or content and press
.
Once you have blocked a rating or content, all higher ratings or contents will be
automatically blocked.
To view a blocked program:
Press ENTER on the remote control, then use the 0-9 buttons to enter your
password.
To reset your password:
1 Move the cursor to CHANGE PASSWORD press
.
2 Use the 0-9 buttons to create a new password, enter again to confirm.
In the event that you forget your password, see page 33.
CHANGE PASSWORD
PARENTAL CONTROL
RATING: CHILD
Move Exit
MENU
Select
MENU
PARENTAL LOCK: ON
CHANGE PASSWORD
PARENTAL CONTROL
RATING: CHILD
Move Exit
MENU
Select
MENU
PARENTAL LOCK: ON
Using Your Menus (continued)
29
Programming the remote
You can use the supplied remote control to
operate Sony or non-Sony video equipment.
Operating Video Equipment
1
Press CODE SET.
2
Press VTR/DVD (FUNCTION).
3
Use the 0-9 buttons to key in the
manufacturer's code number from the
following chart.
4
Press ENTER.
VCR code numbers
Manufacturer Code
Sony 301, 302, 303
Admiral (M. Ward) 327
Aiwa 338, 344
Audio Dynamic 314, 337
Broksonic 319, 317
Canon 309, 308
Citizen 332
Craig 302, 332
Criterion 315
Curtis Mathes 304, 338, 309
Daewoo 341, 312, 309
DBX 314, 336, 337
Dimensia 304
Emerson 319, 320, 316, 317, 318, 341
Fisher 330, 335
Funai 338
General Electric 329, 304, 309
Go Video 322, 339, 340
Goldstar 332
Hitachi 306, 304, 305,338
Instant Replay 309, 308
JC Penney 309, 305, 304, 330, 314, 336, 337
JVC 314, 336, 337, 345, 346, 347
Kenwood 314, 336, 332, 337
LXI (Sears) 332, 305, 330, 335, 338
Magnavox 308, 309, 310
Marantz 314, 336, 337
Marta 332
Memorex 309, 335
Minolta 305, 304
Mitsubishi/MGA 323, 324, 325, 326
Multitech 325, 338, 321
NEC 314, 336, 337
Olympic 309, 308
Optimus 327
Panasonic 308, 309, 306, 307
Pentax 305, 304
Philco 308, 309
Philips 308, 309, 310
Pioneer 308
Quasar 308, 309, 306
RCA/PROSCAN 304, 305, 308, 309, 311,
312, 313, 310, 329
Realistic 309, 330, 328, 335, 324, 338
Sansui 314
Samsung 322, 313, 321
Sanyo 330, 335
Scott 312, 313, 321, 335, 323, 324, 325, 326
Sharp 327, 328
Shintom 315
Signature 2000 (M. Ward) 338, 327
SV2000 338
Sylvania 308, 309, 338, 310
Symphonic 338
Tashiro 332
Tatung 314, 336, 337
Teac 314. 336, 338, 337
Technics 309, 308
Toshiba 312, 311
Wards 327, 328, 335, 331, 332
Yamaha 314, 330, 336, 337
Zenith 331
Operating a VCR
To turn on or off
To select a
channel directly
To change
channels
To record
To play
To stop
To fast forward
To rewind the tape
To pause
To scan
To change input
mode
Buttons on the
remote control
Press VTR/DVD (POWER).
Press the 0-9 buttons.
Press CH +/–.
Press ( and r
simultaneously.
Press (.
Press p.
Press ).
Press 0.
Press P.
To resume normal playback,
press again or press (.
Press ) or 0 during
playback.
To resume normal playback,
release the button.
Press TV/VTR.
To Next Page