Sony TRINITRON KV-S3411A - Page 8

To tune in a channel
by frequency
Alter selecting F in
step 5, enter three
digits using the num-
ber buttons,
If you have made a
mistake
Press + to go
back to the previous
position.
To go back to main
menu
Keep pressing +.
To go back to the
normal TV picture
Press MENU.
-
-b
-d
Using A + or V -, select the programme position (number but-
ton) to which you want to preset a channel, and press OK.
Select if necessary, a video input source (EXT) with A + or V -.
Then press OK. The CH position will be highlighted.
(See Fig. 8.)
Using A + or V —, select C (to preset a regular channel) or F
(to tune in by frequency) and press OK.
The first element of the »CH« number will be highlighted.
If you have selected EXT in step 4, select the video input source
with A + or V ~. (See Fig. 9.)
There are two ways to preset channels. if you know the channel
number, go to step »6-Manuat«,
or
it you don’t know the channel number, go to step »6-Search=.
Manual
Select the first element of the »CH« number with A + or V — or
the number buttons and press OK.
The second element of the »CH« number will be highlighted.
Select the second element of the number with A + or V - or the
number buttons.
The selected number appears. (See Fig. 10.)
Press OK.
The »SEARCH- position is highlighted and the selected channel
is now stored. (See Fig. 11.)
Press OK until the cursor appears by the next programme
position.
Repeat steps 3 to 6 to preset other channels.
Search
Press OK repeatedly until the colour of the SEARCH position
changes.
Start searching for the channel with A + (up) or V — (down).
The CH position changes colour. (See Fig. 12.)
The CH number starts counting up or downwards. When a chan-
nel is found, it stops. (See Fig. 13.)
Press OK if you want to store this channel. If not, press A + or
V - to continue channel searching.
Press OK until the cursor appears by the next programme
position.
Repeat steps 3 to 6 to preset other channels.
Fig. 8.
Fig. 9.
Fig. 10.
Fig. 11.
Fig. 12.
Fig. 13.
For programme
positions beyond 15
The display scolls
automatically.
If you have made a
mistake
Press + to go
back to the previous
position.
To go back to main
menu
Keep pressing —.
To go back to the
normat TV picture
Press MENU.
10
1-3. ADDITIONAL PRESETTING FUNCTIONS
This section shows you additional presetting functions such as
exchanging or skipping programme positions, captioning a sta-
tion name, manual fine-tuning, and using the parental lock.
Before you begin
Check that the Full Function side of the Remote Commander is
visible.
Locate the Menu operation buttons.
Exchanging Programme
Positions
With this function, you can exchange the programme positions to
a preferable order.
Press MENU to display the main menu.
Select »Preset« with A + or V — and press OK.
The PRESET menu appears.
Select »Programme Exchange« with A + or Y — and press OK,
The PROGRAMME EXCHANGE menu appears. (See Fig. 14.)
Using d+ oc — . select the prooreryne postion you Wark 2
exchange with another and press
TA Sob of #a beeoed eatin one: (See Fig. 15.)
Using 4 + or Y —, select the programme position to be exchan-
ged and press OK. Now the two programme positions have been
exchanged. (See Fig. 16.)
Repeat steps 4 and 5 to exchange other programme positions.
Tuning in a Channel Temporarily
You can tune in a channel temporarily, even when it has not been
preset. Use the buttons on the Full-Function side of the Remote
Commander.
Press C on the Remote Commander.
The indication =C« appears on the screen.
Enter the double-digit channel number using the number buttons
(e.g. for channel 4, first press 0, then 4).
The channe! appears.
However, the channet wil not be stored.