EasyManua.ls Logo

Sony URX-P40 - User Manual

Sony URX-P40
56 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
UHF Wireless Microphone Package
UHF Synthesized Transmitter
UHF Synthesized Wireless Microphone
UHF Synthesized Diversity Tuner
Operating Instructions
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
UWP-D21/D22/D26/D27
UTX-B40
UTX-M40
UTX-P40
URX-P40
URX-P41D
5-042-114-11 (1)
© 2022 Sony Corporation

Table of Contents

Questions and Answers

  • B
    Brandi MullinsSep 9, 2025
    Why the transmitter channel cannot be set with infrared transmission on Sony Microphone system?
    • J
      Jacob MathisSep 9, 2025
      If you cannot set the transmitter channel with infrared transmission on your Sony Microphone system, reduce the distance between the infrared receptor on the transmitter and the infrared transmission port on the tuner to within about 20 cm (8 in.). Also, place the transmitter and tuner as close to each other as possible to avoid interference from other devices or direct sunlight.
  • A
    Adrienne LinAug 22, 2025
    Why is there sound interruption or noise in my Sony Microphone system?
    • N
      Noah AguilarAug 22, 2025
      If you're experiencing interruption or noise with your Sony Microphone system, ensure that the channel setting on both the transmitter and tuner are the same. Also, avoid using two or more transmitters on the same channel. Refer to the frequency list on the provided CD-ROM to reconfigure the channel on each transmitter. The channel plan is set so that no signal interference occurs when two or more transmitters are used simultaneously. Set each transmitter to a different channel within the same channel group. Use channels separated by at least two channels (250 kHz).
  • J
    justinmiddletonSep 6, 2025
    Why does the RF indicator light up when the transmitter is off on my Sony Microphone system?
    • H
      hendersonleahSep 6, 2025
      If the RF indicator on the tuner of your Sony Microphone system lights up even when the transmitter is off, jamming radio waves are being received. Set the channel on the tuner to one where the RF indicator doesn't light up, or use the Clear Channel Scan function to switch to a channel without interference. Then, set the transmitter to the same channel as the tuner. If using multiple transmitters, switch to a channel group that isn't affected.
  • S
    steinjeffreySep 5, 2025
    What to do if Sony Microphone system does not turn off?
    • G
      Gabrielle BowenSep 5, 2025
      If your Sony Microphone system does not turn off, release the locked status in the POWER LOCK menu. Alternatively, if the unit is set so that power cannot be turned on/ off using the POWER/MUTE button, set the POWER/MUTE menu to POWER/MUTE, or turn the unit off using the POWER button.
  • W
    wileythomasSep 3, 2025
    Why do the batteries become drained quickly on Sony Microphone system?
    • W
      websterbobbySep 3, 2025
      If the batteries in your Sony Microphone system are draining quickly, replace them with new ones. Use alkaline batteries instead of manganese, as alkaline batteries last more than twice as long. Be aware that batteries drain faster in cold conditions.
  • J
    John LangSep 2, 2025
    How to troubleshoot a Sony Microphone system that does not turn on?
    • C
      Cody AcevedoSep 2, 2025
      If your Sony Microphone system doesn't turn on, make sure the batteries are inserted with the correct polarity. Replace the batteries if they're low. Clean the battery terminals and the compartment with a cotton swab if they're dirty. If POWER SOURCE is set to BATT ONLY, ensure batteries are inserted.
  • L
    Leah SandovalAug 31, 2025
    What to do if the sound is distorted on Sony Microphone system?
    • M
      Mr. Dan KingAug 31, 2025
      If the sound from your Sony Microphone system is distorted, the attenuation level on the transmitter might be too low or set to 0; adjust it so the audio isn't distorted. Change the GAIN MODE setting if it's set to 15dB BOOST. The channel settings on the transmitter and tuner should match. Ensure you're using headphones with a stereo mini jack, not a monaural one.
  • K
    Keith EspinozaAug 30, 2025
    Why is the sound so weak on my Sony Microphone system?
    • N
      Natalie LeeAug 30, 2025
      If the sound from your Sony Microphone system is weak, the attenuation level on the transmitter might be too high; adjust it to an appropriate level. Also, check the volume on the amplifier or mixer and adjust it accordingly. Ensure the transmitter is set to microphone input, not line level. The compander mode setting on the transmitter should match the one on the tuner.
  • W
    William BlevinsAug 29, 2025
    Why is the noise louder when connected with SMAD-P5 on my Sony URX-P40 Microphone system?
    • H
      hunterscottAug 29, 2025
      To resolve the issue of louder noise when connected with SMAD-P5 compared to the XLR-BMP conversion output cable on your Sony Microphone system, adjust the reference input level and reference recording level of the camcorder, or adjust the OUTPUT LEVEL on the tuner to set the appropriate audio level.
  • C
    Crystal BakerAug 27, 2025
    What to do if there is no sound from my Sony Microphone system?
    • D
      Derek PotterAug 27, 2025
      If there is no sound from your Sony Microphone system, verify that the channel setting is the same on both the transmitter and tuner. Confirm that the transmitter is on and reduce the distance between the transmitter and tuner. Ensure the transmitter is set to microphone input, not line level. The compander mode setting must be the same on both devices. Check if the transmitter is muted and release it by pressing the POWER/MUTE button. Review the MUTE SETTING menu and audio output connector settings. If using the SMAD-P5, ensure the Analog/Digital switch is correctly set. For microphones connected to the MIC INPUT, configure the microphone setting in the MIC SELECT menu to match the microphone type.

Summary

Name and Function of Parts

Body-pack Transmitter (UTX-B40) Parts

Identifies and describes the components of the UTX-B40 body-pack transmitter.

Hand-held Microphone (UTX-M40) Parts

Plug-on Transmitter (UTX-P40) Parts

Portable Diversity Tuner (URX-P40) Parts

Portable Diversity Tuner (URX-P41 D) Parts

Power Supply

Inserting Batteries

Provides instructions on how to correctly insert AA batteries into the devices.

USB Power Supply

Explains how to power the devices using a USB connector.

Tuner Settings

Tuner Menu Structure and Operation

Setting the Receive Channel

Guide on selecting the appropriate channel group and number for reception.

Clear Channel Scan

Transmitter Settings

Transmitter Menu Structure and Operation

Setting the Transmit Channel

Guide on selecting the appropriate channel group and number for transmission.

Audio Input Attenuation

Audio Gain Control

Troubleshooting

Unit Power Issues

Solutions for problems related to the unit not turning on.

Audio Signal Problems

Troubleshooting steps for weak, distorted, or noisy audio signals.

Channel Setting Issues

Resolving problems with setting or receiving channels.

Sony URX-P40 Specifications

General IconGeneral
Audio Frequency Response20 Hz to 20 kHz
Tuning Steps25 kHz
Frequency Range470 to 608 MHz
ModulationFM
Signal-to-Noise Ratio> 100 dB
Operating RangeUp to 100 m (328 ft)
Distortion< 0.5%
Antenna TypeDiversity Antenna
Operating Temperature0°C to 50°C
Storage Temperature-20°C to 60°C
Battery TypeAA
Power SupplyDC 3V

Related product manuals