To Next PageTo Next PageWhy won't my Sony Projector turn on?
If your Sony Projector isn't turning on, there are a few potential reasons. If the power was recently turned off and on quickly using the I / 1 key, wait about 60 seconds before trying again. Also, make sure the lamp cover and the air filter cover are securely closed.
What does it mean when the ON/STANDBY light flashes red on my Sony VPL-CX125?
If the ON/STANDBY indicator on your Sony Projector is flashing red twice repeatedly, it indicates that the internal temperature is unusually high. Check to ensure that nothing is blocking the ventilation holes. If you are using the projector at a high altitude, make sure that “High Altitude Mode” in the Setup menu is set to “On.”
Why won't my Sony VPL-CX125 Projector power on?
If your Sony Projector isn't powering on, it could be due to a few reasons. If the power was recently turned off and on, wait about 60 seconds before trying again. Ensure the lamp cover and air filter cover are securely closed.
What to do if the computer is not displayed in the PC list on my Sony VPL-CX125 Projector?
If your computer isn't showing up in the PC list on your Sony Projector, there are a few things to check: * First, make sure that Projector Station for Air Shot Version 2 is installed and running on your computer. If it's not, install it and start the application. * Next, verify that the network cable is securely connected to the NETWORK connector on the projector. * Also, the network segment (subnet) of the computer and the projector might be different. You may need to configure the PC Registration List on the projector and the Projector Setting window on your computer. * Finally, ensure that the network settings of both the projector and the computer are correctly configured and match each other.
How to adjust the image size on my Sony VPL-CX125 if it extends beyond the screen?
If the image extends beyond the screen on your Sony Projector, and the APA key is pressed although there are black edges around the image, display the full image on the screen and press the APA key. Also, adjust “Shift” in the Signal menu properly.
What to do if my Sony VPL-CX125 has no picture?
If your Sony Projector displays no picture, several factors could be the cause. First, ensure all cables are properly connected. Second, verify that you've selected the correct input source using the INPUT key. Also, check if the picture is muted by pressing the PIC MUTING key. If you're using a computer, ensure the signal is set to output only to an external monitor. Finally, depending on your computer type, you might need to manually switch the output to the projector via specific keys or settings; refer to your computer's manual for guidance.
Why is the image extending beyond the screen on my Sony Projector?
If the image on your Sony Projector extends beyond the screen, it could be due to a couple of reasons. If you've pressed the APA key while there are black edges around the image, display the full image on the screen and then press the APA key. You may also need to adjust the 'Shift' setting in the Signal menu.
How to stop image extending beyond the screen on Sony VPL-CX125 Projector?
If the image extends beyond the screen on your Sony Projector, and you notice black edges around the image, display the full image on the screen and press the APA key.
What to do if there is no picture on my Sony VPL-CX125?
If there is no picture, several factors could be at play. First, ensure all cables are correctly connected. Second, verify that you've selected the correct input source using the INPUT key. Third, check if the picture is muted and, if so, press the PIC MUTING key to release it. Finally, if you're using a computer, confirm that the signal is set to output only to an external monitor.
Why is the picture not clear on my Sony VPL-CX125 Projector?
If the picture on your Sony Projector is not clear, first adjust the focus. If that doesn't work, condensation may have occurred on the lens. Leave the projector on for about two hours to resolve this.
General| Brightness | 3000 ANSI Lumens |
|---|---|
| Resolution | 1024 x 768 (XGA) |
| Contrast Ratio | 2000:1 |
| Display Technology | 3LCD |
| Projection Size | 30 to 300 inches |
| Display Type | LCD |
| Weight | 2.9 kg |
| Input Ports | S-Video, RS-232C |
| Lamp Type | UHP |
| Zoom | 1.2x |
