To Next Page
F
francojosephSep 4, 2025
How to fix a flickering picture on my Sony Projector?
- MMartin CobbSep 4, 2025
If the picture on your Sony Projector flickers, adjust “Dot Phase” in the INPUT SETTING menu.
How to fix a flickering picture on my Sony Projector?
If the picture on your Sony Projector flickers, adjust “Dot Phase” in the INPUT SETTING menu.
Why is my Sony VPL-CX70 power not turning on?
If the power of your Sony Projector is not turning on, it may be because the power has been turned off and on too quickly. Wait about 60 seconds before attempting to turn it on again. Also, make sure that the lamp cover and the air filter cover are securely closed and attached, respectively.
Why won't my Sony VPL-CX70 power on?
If your Sony Projector won't power on, it may be because the power was recently turned off and on too quickly. Wait about 60 seconds before trying to turn it on again. Also, ensure that the lamp cover and the air filter cover are securely closed and attached.
Why is the picture from INPUT A connector colored strange on Sony Projector?
If the picture from INPUT A connector is colored strangely, the setting of “Input-A Signal Sel.” in the SET SETTING menu is incorrect. Select “Computer,” “Video GBR” or “Component” correctly according to the input signal.
Why does my Sony VPL-CX70 Projector say 'Please check Input-A Signal Sel.' even with the correct signal?
If the Sony Projector displays “Please check Input-A Signal Sel.” even when inputting the correct signal from INPUT A, the setting of “Input-A Signal Sel.” on the SET SETTING menu is incorrect. Select “Computer,” “Video GBR” or “Component” correctly according to the input signal.
What to do if the control panel keys do not function on my Sony Projector?
If the control panel keys on your Sony Projector do not function, unlock the control panel keys.
Why is there no picture on my Sony Projector?
If there is no picture on your Sony Projector, verify that all cable connections are correct. Ensure your projector is compatible with DDC2B (Digital Data Channel 2B). If it is, connect the projector to the computer, turn on the projector, and then start the computer. Also, select the correct input source using the INPUT key and press the PIC MUTING key to release picture muting, if activated.
Why can't the computer be controlled with the presentation tool on my Sony VPL-CX70 Projector (VPL-CX76)?
If the computer cannot be controlled with the presentation tool (VPL-CX76 only) and the USB cable is being used or the Air Shot is not being used, use the Remote Commander to operate the device connected via the USB cable. The presentation tool is designed to be used with the Air Shot.
Why does my Sony VPL-CX70 Projector say 'High temp! Probably use in high altitude'?
If the Sony Projector displays “High temp.! Probably use in high altitude. Switch to high altitude mode on? Yes V No v”, and you are using it at an altitude of 1,500 m or higher, set “High Altitude Mode” on the INSTALL SETTING menu to “On.” If this message appears at normal altitudes, check for obstructions blocking the ventilation holes.
What does “Please replace the LAMP” mean on Sony VPL-CX70?
This message indicates that it is time to replace the lamp. Replace the lamp.
Guides for connecting the projector to a computer via USB and video cables.
Steps for powering on, initial setup, and input source management.
Correcting focus, size, tilt, keystone, and side shot distortions.
Adjusting picture mode, volume, contrast, brightness, and color.
Configuring input signals, aspect ratio, and signal adjustment.
Procedures for replacing the lamp and cleaning the air filter.
Solutions for power, display, and image quality problems.
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel with Micro Lens Array |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2500 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
| wireless LAN | Wireless LAN card slot x 1 |
| memory stick | Memory Stick media slot x 1 |
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2000 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
