What does it mean when the ON/STANDBY light flashes red on my Sony VPL-CX125?
If the ON/STANDBY indicator on your Sony Projector is flashing red twice repeatedly, it indicates that the internal temperature is unusually high. Check to ensure that nothing is blocking the ventilation holes. If you are using the projector at a high altitude, make sure that “High Altitude Mode” in the Setup menu is set to “On.”
Why won't my Sony VPL-CX125 Projector power on?
If your Sony Projector isn't powering on, it could be due to a few reasons. If the power was recently turned off and on, wait about 60 seconds before trying again. Ensure the lamp cover and air filter cover are securely closed.
What to do if the computer is not displayed in the PC list on my Sony VPL-CX125 Projector?
If your computer isn't showing up in the PC list on your Sony Projector, there are a few things to check: * First, make sure that Projector Station for Air Shot Version 2 is installed and running on your computer. If it's not, install it and start the application. * Next, verify that the network cable is securely connected to the NETWORK connector on the projector. * Also, the network segment (subnet) of the computer and the projector might be different. You may need to configure the PC Registration List on the projector and the Projector Setting window on your computer. * Finally, ensure that the network settings of both the projector and the computer are correctly configured and match each other.
How to adjust the image size on my Sony VPL-CX125 if it extends beyond the screen?
If the image extends beyond the screen on your Sony Projector, and the APA key is pressed although there are black edges around the image, display the full image on the screen and press the APA key. Also, adjust “Shift” in the Signal menu properly.
How to resolve a noisy picture on a Sony Projector?
If the picture on your Sony Projector appears noisy, especially in the background, try changing the desktop pattern on the connected computer. This issue can arise from the combination of dot input from the connector and the number of pixels on the LCD panel.
How to fix a blurry picture on Sony VPL-CX125 Projector?
If the picture on your Sony Projector is not clear, try adjusting the focus. If condensation has occurred on the lens, leave the projector on for about two hours to allow it to clear.
How to fix a flickering picture on a Sony VPL-CX125?
If the picture on your Sony Projector flickers, adjust the “Dot Phase” in the Signal menu properly.
Why is the picture noisy on my Sony VPL-CX125 Projector?
Noise may appear on the background of your Sony Projector depending on the combination of the numbers of dot input from the connector and numbers of pixel on the LCD panel. To resolve this, change the desktop pattern on the connected computer.
Why is the picture not clear on my Sony VPL-CX125 Projector?
If the picture on your Sony Projector is not clear, first adjust the focus. If that doesn't work, condensation may have occurred on the lens. Leave the projector on for about two hours to resolve this.
What does it mean if ON/STANDBY flashes in red on Sony VPL-CX125 (2 flashes)?
If the ON/STANDBY indicator is flashing red with a repetition rate of 2 flashes, it indicates that the internal temperature is unusually high. Check to ensure that nothing is blocking the ventilation holes. Also, if you are using the projector at a high altitude, ensure that “High Altitude Mode” on the Setup menu is set to “On.”
Details the network presentation and control functions of the projector.
Lists the recommended system requirements for Projector Station for Air Shot Version 2.
Instructions for installing Projector Station for Air Shot Version 2 on a computer.
Steps to connect the network cable and turn on the projector.
Explains how to access the projector's web interface from a computer.
Details how to control projector functions through the web interface.
Covers configuration of owner information, password, date, and time.
Explains how to set and manage administrator and user passwords.
Details how to configure the projector's automatic e-mail reporting features.
Specifies options for scheduling regular, maintenance, and error email reports.
Configuration of email addresses, SMTP/POP servers, and authentication.
Provides solutions for common projector and connection issues.
Explains error messages and their causes/remedies.
General| Brightness | 3000 ANSI Lumens |
|---|---|
| Resolution | 1024 x 768 (XGA) |
| Contrast Ratio | 2000:1 |
| Display Technology | 3LCD |
| Projection Size | 30 to 300 inches |
| Display Type | LCD |
| Weight | 2.9 kg |
| Input Ports | S-Video, RS-232C |
| Lamp Type | UHP |
| Zoom | 1.2x |
To Next Page
