How to fix Sony VPL-CX70 Projector when the power is not turned on?
If the Sony Projector's power is not turning on, wait about 60 seconds before trying to turn it on again if it was recently turned off. Also, ensure that the lamp cover and the air filter cover are securely closed and attached, respectively.
What does 'Please replace the Lamp' mean on my Sony VPL-CX70 Projector?
If the Sony Projector displays the message 'Please replace the Lamp', it indicates that the lamp needs replacing. Replace the lamp. If the message persists after replacement, perform steps 8 and 9 as described in the manual to complete the task. To clear the message, press any key on the projector's control panel or the remote commander.
What does “Please replace the LAMP” mean on Sony VPL-CX70?
This message indicates that it is time to replace the lamp. Replace the lamp.
How to fix the dark picture on my Sony Projector?
If the picture is too dark, it could be due to the following reasons: * The contrast or brightness may not be adjusted properly. Adjust the contrast or brightness in the “Adjust Picture...” menu. * The lamp may have burnt out or is dimming. Replace the lamp with a new one.
Why is the picture from INPUT A connector colored strange on Sony Projector?
If the picture from INPUT A connector is colored strangely, the setting of “Input-A Signal Sel.” in the SET SETTING menu is incorrect. Select “Computer,” “Video GBR” or “Component” correctly according to the input signal.
Why does my Sony VPL-CX70 Projector say 'High temp! Probably use in high altitude'?
If the Sony Projector displays “High temp.! Probably use in high altitude. Switch to high altitude mode on? Yes V No v”, and you are using it at an altitude of 1,500 m or higher, set “High Altitude Mode” on the INSTALL SETTING menu to “On.” If this message appears at normal altitudes, check for obstructions blocking the ventilation holes.
What to do if the control panel keys do not function on Sony VPL-CX70?
If the control panel keys on your Sony Projector do not function, the control panel keys are likely locked. Unlock the control panel keys.
Why is the picture from the INPUT A connector colored strangely on my Sony VPL-CX70 Projector?
If the picture from the INPUT A connector on your Sony Projector appears colored strangely, the “Input-A Signal Sel.” setting in the SET SETTING menu might be incorrect. Select the appropriate option (“Computer,” “Video GBR,” or “Component”) according to your input signal.
How to fix no picture on Sony VPL-CX70 Projector?
If your Sony Projector shows no picture, check the cable connections, ensuring they are correctly connected. If connections are correct, and you still have no picture, make sure the input selection is correct by using the INPUT key. Also, ensure that the picture is not muted by pressing the PIC MUTING key. If you have a VPL-CX76 model, check if the B key is activated and deactivate it using the Presentation Tool.
Why won't my Sony VPL-CX70 power on?
If your Sony Projector won't power on, it may be because the power was recently turned off and on too quickly. Wait about 60 seconds before trying to turn it on again. Also, ensure that the lamp cover and the air filter cover are securely closed and attached.
Guides for connecting the projector to a computer via USB and video cables.
Steps for powering on, initial setup, and input source management.
Correcting focus, size, tilt, keystone, and side shot distortions.
Adjusting picture mode, volume, contrast, brightness, and color.
Configuring input signals, aspect ratio, and signal adjustment.
Procedures for replacing the lamp and cleaning the air filter.
Solutions for power, display, and image quality problems.
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel with Micro Lens Array |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2500 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
| wireless LAN | Wireless LAN card slot x 1 |
| memory stick | Memory Stick media slot x 1 |
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2000 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
To Next Page
