To Next PageTo Next Page
How to fix a blurry picture on Sony VPL-CX70?
If the picture on your Sony Projector is not clear, try adjusting the focus. If that doesn't work, condensation might have accumulated on the lens. Leave the projector on for about two hours to resolve this.
How to adjust the image size on Sony VPL-CX70?
If the image extends beyond the screen on your Sony Projector, try displaying the full image on the screen and pressing the APA key. Alternatively, adjust the “Shift” setting on the INPUT SETTING menu.
Why is my Sony VPL-CX70 picture flickering?
If the picture on your Sony Projector flickers, adjust the “Dot Phase” setting on the INPUT SETTING menu.
How to fix incorrect color balance on Sony VPL-CX70 Projector?
To correct the color balance on your Sony Projector, first, adjust the picture settings. If the issue persists, check that the “Color System” in the SET SETTING menu matches the color system being input.
What does “Please replace the LAMP” mean on Sony VPL-CX70?
This message indicates that it is time to replace the lamp. Replace the lamp.
What does 'Please replace the Lamp' mean on my Sony VPL-CX70 Projector?
If the Sony Projector displays the message 'Please replace the Lamp', it indicates that the lamp needs replacing. Replace the lamp. If the message persists after replacement, perform steps 8 and 9 as described in the manual to complete the task. To clear the message, press any key on the projector's control panel or the remote commander.
How to fix Sony VPL-CX70 Projector when the power is not turned on?
If the Sony Projector's power is not turning on, wait about 60 seconds before trying to turn it on again if it was recently turned off. Also, ensure that the lamp cover and the air filter cover are securely closed and attached, respectively.
Why is the LAMP/COVER indicator flashing on my Sony VPL-CX70 Projector?
If the Sony Projector's LAMP/COVER indicator is flashing, make sure that the lamp cover and the air filter cover are securely attached. If the lens protector did not open, slide it open by hand in case of emergency, and then press the ?/1 key. If the issue persists, the electrical system may have broken down, and you should consult with qualified Sony personnel.
What to do if my Sony VPL-CX70 has no picture?
If your Sony Projector shows no picture, first ensure all cables are properly connected. Then, verify that you've selected the correct input source using the INPUT key. Lastly, if you're using a computer, make sure the signal is set to output only to an external monitor.
What does 'Please clean the filter' mean on my Sony VPL-CX70?
If you see the message 'Please clean the filter' on your Sony Projector, it means it is time to clean the filter. Clean the filter.
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel with Micro Lens Array |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2500 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
| wireless LAN | Wireless LAN card slot x 1 |
| memory stick | Memory Stick media slot x 1 |
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2000 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
