To Next PageTo Next Page
What to do if the powered tilt adjuster and the lens protector do not close on my Sony VPL-CX70 Projector?
If the powered tilt adjuster and the lens protector do not close on your Sony Projector, it could be due to unplugging the AC power cord while the projector was on. Reconnect the power cord, turn the projector on, and then turn it off properly.
How to fix a noisy picture on Sony VPL-CX70 Projector?
To address a noisy picture on your Sony Projector, change the desktop pattern on the connected computer.
Why is there no picture on my Sony Projector?
If there is no picture on your Sony Projector, verify that all cable connections are correct. Ensure your projector is compatible with DDC2B (Digital Data Channel 2B). If it is, connect the projector to the computer, turn on the projector, and then start the computer. Also, select the correct input source using the INPUT key and press the PIC MUTING key to release picture muting, if activated.
Why is there no sound from my Sony Projector?
If you're not getting any sound from your Sony Projector, first, check all cable connections to ensure they are properly connected. Make sure you are using a no-resistance stereo audio cable. Also, verify that the audio is not muted by pressing the AUDIO MUTING key. Finally, adjust the sound using the VOLUME +/– key on the Remote Commander or adjust “Volume” in the PICTURE SETTING menu.
What to do if the picture is too dark on my Sony VPL-CX70 Projector?
If the picture on your Sony Projector is too dark, adjust the contrast or brightness in the “Adjust Picture...” menu. If that doesn't help, the lamp may be burnt out or dimming, and you may need to replace it with a new one.
What to do if my Sony Projector Remote Commander does not work?
If the Remote Commander for your Sony Projector isn’t working, replace the batteries with new ones. Also, check that the COMMAND ON/OFF switch is set to ON and the PJ/NETWORK selector switch is set to PJ.
What to do if the picture is not clear on my Sony Projector?
If the picture on your Sony Projector is not clear, try adjusting the focus. If that doesn't work, condensation may have occurred on the lens. If so, leave the projector on for about two hours to clear the condensation.
What does it mean when the LAMP/COVER indicator flashes on my Sony VPL-CX70?
If the LAMP/COVER indicator is flashing on your Sony Projector, it means the lamp cover or the air filter cover is detached. Attach the cover securely. It could also indicate that the lens protector does not open due to a problem. In that case, slide the lens protector by hand, and then press the I/1 key.
What does it mean when the LAMP/COVER indicator lights up on my Sony Projector?
If the LAMP/COVER indicator lights up on your Sony Projector, it could mean that the lamp has reached the end of its life and needs to be replaced. Alternatively, the lamp may be overheating. Wait for 60 seconds to cool down the lamp before turning the power on again.
What does it mean when the TEMP/FAN indicator lights up on my Sony VPL-CX70?
If the TEMP/FAN indicator lights up on your Sony Projector, it means the internal temperature is unusually high. Check to ensure that nothing is blocking the ventilation holes. If you are using the projector at a high altitude, make sure that “High Altitude Mode” in the INSTALL SETTING menu is set to “On.”
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel with Micro Lens Array |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2500 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
| wireless LAN | Wireless LAN card slot x 1 |
| memory stick | Memory Stick media slot x 1 |
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.79-inch XGA LCD panel |
| projection lens | 1.2 times F1.6 to 1.78, f23.5 to 28.2 mm |
| lamp | 165 W/135 W UHP |
| screen coverage | 40 to 300 inches (measured diagonally) |
| keystone correction range | Max. ±30° vertical, ±20° horizontal |
| light output | 2000 ANSI lm (lamp mode high) |
General| speaker | Mono 1 W (max.) x 1 |
|---|---|
| power requirements | AC 100 to 240 V, 50/60 Hz |
| power consumption | Max 240 W |
| standby power consumption | 9 W (standard), 0.5 W (low) |
| operating temperature | 0 to 35 ºC (32 to 95 ºF) |
| operating humidity | 35% to 85% (no condensation) |
| dimensions | 298 x 69 x 244 mm |
| mass | Approx. 2.9 kg |
| heat dissipation | 819 BTU |
Input/Output| video input | S Video Y/C Mini DIN 4-pin, Composite RCA pin jack |
|---|---|
| audio | Stereo mini jack |
| input A | RGB/Component Analog RGB/Component (HD D-sub 15 pin female x 1) |
| USB | Upstream (B type, female x 1) |
