To Next PageTo Next PageWhat to do if my Splendide WDV2200XCD doesn't drain and shows fault code F9E1?
If your Splendide Washer/Dryer isn't draining and shows the F9E1 fault code: * Clean the pump filter. * Check if the drain hose is bent. * Ensure the drainage duct isn't clogged.
What to do if my Splendide WDV2200XCD Washer/Dryer does not fill with water?
If your Splendide Washer/Dryer isn't filling with water or shows the F8E1 error code, check these: * Ensure the water tap is fully opened. * Confirm the water inlet hose is correctly connected to the tap. * Make sure the hose isn't bent or kinked. * Use the water supply hoses that came with the machine, as flood-safe hoses might restrict water flow. * Verify that the water pressure isn't too low. * Check if the water inlet valve strainer is plugged.
Why my Splendide Washer/Dryer does not switch on?
If your Splendide Washer/Dryer isn't turning on, make sure it's properly plugged into a grounded 3-prong outlet with sufficient contact. Also, verify that the outlet has power.
What to do if the wash cycle does not start on my Splendide WDV2200XCD?
If the wash cycle on your Splendide Washer/Dryer isn't starting, consider the following: * Ensure the washer-dryer door is completely closed. * Confirm that you've pressed the ON/OFF button. * Make sure you've pressed the START/PAUSE button. * Check if the Delay Start button is activated. * Verify you're pressing the START/PAUSE button for the correct duration (2 seconds); holding it too long or too short may prevent the cycle from starting.
Why does my Splendide WDV2200XCD Washer/Dryer vibrate so much?
If your Splendide Washer/Dryer is vibrating excessively during the spin cycle: * Ensure that the transport bolts were correctly removed during installation. * Check that the washer-dryer is properly leveled. * Make sure the washer-dryer isn't squeezed too tightly between furniture, cabinets, or the wall; provide some extra space around the machine.
Why is my Splendide Washer/Dryer leaking?
If your Splendide Washer/Dryer is leaking, check these: * Ensure the water inlet hose is properly screwed on. * Make sure the detergent dispenser drawer isn't obstructed. * Verify the drain hose is correctly attached. * Inspect the rubber washer (gasket) in the inlet hose for damage.
Why does my Splendide WDV2200XCD continuously load and unload water?
If your Splendide Washer/Dryer is continuously loading and unloading water, check the following: * Ensure the drain hose is fitted between 25 and 34 inches from the floor. * Make sure the free end of the hose isn't immersed in water. * Verify the drain pipe fits loosely but securely in the standpipe, and that it is not taped to the standpipe, allowing for an air gap.
How to reduce excessive foam in my Splendide WDV2200XCD Washer/Dryer?
If you see too much foam in your Splendide Washer/Dryer: * Ensure the detergent is suitable for machine washing (look for “for washing machines” or “hand and machine wash” on the label). * Make sure you're not using too much detergent. * Only use HE (High Efficiency) detergent.
What to do if the access door won’t open on my Splendide WDV2200XCD?
If the access door on your Splendide Washer/Dryer won’t open: * The door lock may be activated due to a high water level. Try running a Spin + Drain cycle to remove the water. * There may have been a power loss. Ensure the machine is powered on, or try unplugging it and plugging it back in.
What does 'cL' mean on my Splendide WDV2200XCD display?
If the display on your Splendide Washer/Dryer shows 'cL', run a Clean Washer Cycle. The machine prompts this every 30 cycles.
General| Type | Washer/Dryer Combo |
|---|---|
| Drying Method | Vented |
| Energy Star Certified | No |
| Voltage | 120V |
| Amperage | 15A |
| Color | White |
| Width | 23.5 inches |
Essential safety precautions to mitigate risks associated with using the appliance.
Steps for removing packaging and ensuring the appliance is stable.
Procedure for removing transit screws and spacers to allow proper operation.
Required clearances for free-standing or built-in installation.
Instructions for connecting the water supply hoses to the machine.
Requirements for the standpipe and drain hose setup.
Steps for connecting the drain hose to a standpipe, sink, or drainpipe.
Information regarding power requirements and connections.
Crucial steps for safely grounding the appliance.
Specifications and technical data for the washer-dryer.
Description of the appliance's control panel buttons and functions.
Details on available wash cycles, temperatures, spin speeds, and loads.
Overview of the main components of the washer-dryer.
How to use and maintain the detergent dispenser compartments.
Instructions for using the bleach cycle and its limitations.
Detailed explanation of each wash cycle and its appropriate use.
Explanation of the information shown on the appliance's display.
Initial setup and first operation of the washer-dryer.
Step-by-step guide for routine daily operation.
How to temporarily stop and resume a wash cycle.
Procedure for opening the door during or after a cycle.
Steps to modify or cancel a cycle that is currently in progress.
What to do once a wash cycle has completed.
Explanation of available cycle options and their compatibility.
Helpful advice for optimizing wash and dry performance.
Manual procedure to open the door in case of a power outage.
How to inspect the water supply hose for damage and leaks.
Procedure for cleaning the filters in the water inlet valves.
Steps for removing and cleaning the detergent dispenser drawer.
Guide to cleaning the water filter and draining any remaining water.
Steps for winterizing the appliance using antifreeze.
Alternative method for winterizing using antifreeze in the drum.
Steps to prepare the appliance for use after winter storage.
