ENGLISH
Original Instruction
©2017 Stanley Black& Decker inc.
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically or
mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information provided is
based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening pursues
a policy of continuous product improvement and therefore the products may be subject to change. The information provided
is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered Fastening cannot
be held liable for any damage resulting from deviations from the original specifications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept
any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening
will not accept any liability for damage resulting from activities carried out by third parties. The working names, trade names,
registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free, pursuant to the
legislation with respect to the protection of trade marks.
CONTENT
1.
SAFETY DEFINITIONS
8
2.
SPECIFICATION
9
2.1.
TOOL SPECIFICATIONS
9
2.2 TOOL DIMENSION
10
2.3 PLACING SPECIFICATION
11
2.4 MAIN COMPONENTS LIST
12
2.5 STANDARD NOSE EQUIPMENT
12
3.
TOOL SET UP
13
3.1 NOSE EQUIPMENT (Ref. fig. 2)
13
3.2 AIR SUPPLY (Ref. fig. 3)
13
3.3 PRINCIPLE OF OPERATION
14
4.
OPERATION PROCEDURE
14
4.1 TOOL OPERATION (Ref. fig. 1, 4, 5, 6)
14
4.2 EMPTYING THE MANDREL COLLECTOR. (Ref. fig. 1)
14
5.
SERVICING THE TOOL
15
5.1 MAINTENANCE FREQUENCY
15
5.2 NOSE EQUIPMENT
15
5.3 DAILY SERVICING
15
5.4 WEEKLY SERVICING
15
5.5 SERVICE KIT
16
5.6 PRIMING
16
6.
MAINTENANCE
17
6.1 DISMANTLING THE TOOL
18
7.
TROUBLESHOOTING GUIDE
21
8.
GENERAL SAFETY DATA
22
8.1 HYSPIN° VG32 OIL SAFETY DATA
22
8.2 MOLY LITHIUM GREASE EP 3753 SAFETY DATA
23
8.3 MOLYKOTE° 55M GREASE SAFETY DATA
24
8.4 MOLYKOTE° 111 GREASE SAFETY DATA
24
POP
Avdel°
7
Original Instruction
©2017 Stanley Black & Decker inc.
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically or
mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information provided is
based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening pursues
a policy of continuous product improvement and therefore the products may be subject to change. The information provided
is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered Fastening cannot
be held liable for any damage resulting from deviations from the original specications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept
any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening
will not accept any liability for damage resulting from activities carried out by third parties. The working names, trade names,
registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free, pursuant to the
legislation with respect to the protection of trade marks.
CONTENT
1. SAFETY DEFINITIONS .................................................................................................................................8
2. SPECIFICATION ...........................................................................................................................................9
2.1. TOOL SPECIFICATIONS ....................................................................................................................................................................9
2.2 TOOL DIMENSION ........................................................................................................................................................................10
2.3 PLACING SPECIFICATION ..........................................................................................................................................................11
2.4 MAIN COMPONENTS LIST ...........................................................................................................................................................12
2.5 STANDARD NOSE EQUIPMENT .................................................................................................................................................12
3. TOOL SET UP .............................................................................................................................................13
3.1 NOSE EQUIPMENT (Ref. g. 2) ................................................................................................................................................... 13
3.2 AIR SUPPLY (Ref. g. 3) .................................................................................................................................................................13
3.3 PRINCIPLE OF OPERATION..........................................................................................................................................................14
4. OPERATION PROCEDURE .........................................................................................................................14
4.1 TOOL OPERATION (Ref. g. 1, 4, 5, 6) ......................................................................................................................................14
4.2 EMPTYING THE MANDREL COLLECTOR. (Ref. g. 1) .......................................................................................................... 14
5. SERVICING THE TOOL ...............................................................................................................................15
5.1 MAINTENANCE FREQUENCY .....................................................................................................................................................15
5.2 NOSE EQUIPMENT ......................................................................................................................................................................... 15
5.3 DAILY SERVICING ...........................................................................................................................................................................15
5.4 WEEKLY SERVICING ....................................................................................................................................................................... 15
5.5 SERVICE KIT ......................................................................................................................................................................................16
5.6 PRIMING ............................................................................................................................................................................................16
6. MAINTENANCE ......................................................................................................................................... 17
6.1 DISMANTLING THE TOOL ............................................................................................................................................................18
7. TROUBLESHOOTING GUIDE ...................................................................................................................21
8. GENERAL SAFETY DATA ..........................................................................................................................22
8.1 HYSPIN® VG32 OIL SAFETY DATA ........................................................................................................................................... 22
8.2 MOLY LITHIUM GREASE EP 3753 SAFETY DATA. .................................................................................................................23
8.3 MOLYKOTE® 55M GREASE SAFETY DATA...............................................................................................................................24
8.4 MOLYKOTE® 111 GREASE SAFETY DATA ..............................................................................................................................24
ENGLISH
7
To Next Page
Loading...
Need help?
General
