To Next PageTo Next PageWhy does my Stanley Tara fire go out?
If the fire in your Stanley Boiler goes out, it might be due to air starvation or insufficient draught. To resolve this, open the lower spin wheel and top air control lever. Also, check the flue for any obstructions and sweep it if necessary. It is recommended to seek advice from a chimney specialist.
What to do if Stanley Tara smokes when lighting up?
If your Stanley Boiler smokes when lighting up, it's likely because the flue duct is cold. To fix this, burn paper and kindling to increase the heat.
How to stop Stanley Tara Boiler fire burning too quickly?
If the fire in your Stanley Boiler burns too quickly, it could be due to too much draught or poor quality wood/fuel. Make sure the lower spin wheel is closed and partially close the top air control lever. Avoid continuously burning small wood, sticks, bundles, or carpentry off-cuts like plywood or pallets.
What to do if Stanley Tara smokes while burning?
If your Stanley Boiler smokes while burning, it could be due to insufficient draught, down draught, or the room being in decompression. Consult a chimney specialist. Check that the flue is not obstructed, sweep if necessary. Consider installing an anti-down draught cowl. Consult your dealer. If you have Mechanical Ventilation, make sure an outside air intake is installed for the chimney.
Why is my Stanley Tara Boiler giving low heat output?
If your Stanley Boiler is giving low heat output, it is likely due to the use of incorrect fuels. Use the recommended fuel.
How to fix Stanley Tara Boiler fire difficult to start?
If the fire in your Stanley Boiler is difficult to start, it might be because of unseasoned, damp, or poor-quality wood, or logs that are too big. Use only the recommended fuel. To light the fire, use small, very dry twigs, and to maintain the fire, use split logs.
What causes excessive condensation on the Stanley Tara Boiler?
Excessive condensation on your Stanley Boiler can be caused by cold water being circulated or fuel with excessive moisture content. Check that the pipe thermostat is fitted and set correctly. Season fuel to achieve lower moisture content.
Why does Stanley Tara fire shuts down after a period of time?
If the fire in your Stanley Boiler shuts down after a period of time, it may be due to insufficient water circulation through the boiler. In this case, check the plumbing.
Details warranty periods and parts covered for the stove.
Outlines what the warranty does not cover, including negligence and wear and tear.
Checklist items related to the flue system installation requirements.
Checklist items regarding the correct placement of the stove.
Checklist items for ensuring adequate air supply for combustion.
Checklist items for plumbing and electrical work compliance.
Table showing calorific values for different solid fuels.
Tips for safe and efficient operation, including fuel types and cleaning.
Guidance on handling, fire cement, asbestos, and metal parts safety.
Steps for initial assembly before positioning the stove.
Requirements for electrical work to be done by a qualified electrician.
Guidelines for connecting the stove to a suitable chimney of the correct size and type.
Instructions for cleaning the chimney through the stove or providing a soot box.
Detailed steps for configuring the stove for a top flue exit.
Instructions for connecting the flue connector pipe at the rear.
Explains how down draughts affect flue performance and suggests solutions.
Discusses requirements for air vents, their placement, and materials.
Specific ventilation requirements for properties with low air permeability.
Details on using an outside air kit for primary air supply.
Precautions when installing the stove in a dwelling with an HRV system.
Conditions to consider when selecting a location for the stove.
Specifies minimum clearances to combustible materials for different models.
Requirements for a floor protector on combustible floors.
Details on flue outlet size and water connection BSP.
Importance of a pipe thermostat for activating the water circulation pump.
Plumbing must comply with relevant regulations and practices.
Describes the gravity circuit for domestic hot water using an indirect cylinder.
Recommendation for using an injector tee for stable water flow between circuits.
Maintaining return water temperature to avoid condensation and potential overheating.
Connecting the DHW model to a gravity system, checking soundness and insulation.
Connecting a direct domestic cylinder to the DHW stove.
Connecting an indirect domestic cylinder to the DHW stove.
Steps for commissioning, checking operation, and handover to the customer.
Checks for dampers, catches, and flue connections.
Details the primary, window wash, and secondary air controls for different models.
Information on recommended fuels and storage, and what fuels to avoid.
Tables detailing technical specifications, outputs, and efficiency for different models.
Step-by-step guide for lighting the stove.
Procedure for riddling the fire and adding fuel.
Advice on slow burning, its effects on glass, and control settings.
Instructions on removing and safely disposing of ash.
Recommendation for monthly cleaning of flue pathways and annual chimney cleaning.
How to adjust the door latch and when to replace rope seals.
Frequency and method for cleaning the chimney and flue liner.
How the glass self-cleans and how to clean it manually.
Tips for cleaning and maintaining vitreous enamel finishes.
Specific cleaning instructions for matt black/Senotherm finishes.
Warning about frozen water systems and not lighting the stove.
Advice on cleaning and preparing the stove for storage.
Immediate actions to take if persistent fume emission occurs.
General advice for fire safety, including smoke detectors and evacuation plans.
Step-by-step guide for replacing the stove's glass window.
Requirement for CO alarms and actions to take if one sounds.
General