ENGLISH
www.stiebel-eltron.com SH S | 15
CONTENTS | SPECIAL INFORMATION
SPECIAL INFORMATION
OPERATION
1. General information ��������������������������������������� 16
1.1 Safety instructions ����������������������������������������������16
1.2 Other symbols in this documentation ���������������������� 16
1.3 Units of measurement �����������������������������������������16
2. Safety �������������������������������������������������������� 16
2.1 Intended use �����������������������������������������������������16
2.2 General safety instructions ����������������������������������� 16
2.3 Test symbols ����������������������������������������������������� 17
3. Appliance description ������������������������������������� 17
3.1 Frost protection ������������������������������������������������� 17
4. Settings ����������������������������������������������������� 17
5. Cleaning, care and maintenance ������������������������� 17
6. Troubleshooting �������������������������������������������� 18
INSTALLATION
7. Safety �������������������������������������������������������� 18
7.1 General safety instructions ����������������������������������� 18
7.2 Instructions, standards and regulations �������������������18
8. Appliance description ������������������������������������� 18
8.1 Standard delivery �����������������������������������������������18
8.2 Accessories ������������������������������������������������������� 18
9. Preparations ������������������������������������������������ 18
9.1 Installation site ��������������������������������������������������18
9.2 Fitting the wall mounting bracket ���������������������������18
9.3 Preparing the connecting cables ���������������������������� 19
10. Installation �������������������������������������������������� 19
10.1 Water connection ����������������������������������������������� 19
10.2 Appliance installation ������������������������������������������ 19
10.3 Power supply ���������������������������������������������������� 20
11. Commissioning ��������������������������������������������� 20
11.1 Commissioning �������������������������������������������������� 20
11.2 Recommissioning ����������������������������������������������� 20
12. Settings ����������������������������������������������������� 21
13. Shutting down ���������������������������������������������� 21
14. Troubleshooting �������������������������������������������� 21
15. Maintenance ������������������������������������������������ 22
15.1 Checking the safety valve ������������������������������������� 22
15.2 Draining the appliance ���������������������������������������� 22
15.3 Checking/ replacing the signal anode ��������������������� 22
15.4 Descaling ��������������������������������������������������������� 22
15.5 Anti-corrosion protection �������������������������������������22
16. Specification ������������������������������������������������ 23
16.1 Dimensions and connections ��������������������������������� 23
16.2 Wiring diagrams and terminals ������������������������������ 24
16.3 Heat-up diagram ������������������������������������������������ 25
16.4 Fault conditions ������������������������������������������������� 25
16.5 Details on energy consumption ������������������������������ 25
16.6 Data table ��������������������������������������������������������26
GUARANTEE
ENVIRONMENT AND RECYCLING
SPECIAL INFORMATION
- The appliance may be used by children aged3
and up and persons with reduced physical, sen-
sory or mental capabilities or a lack of experience
and know-how, provided that they are supervised
or they have been instructed on how to use the
appliance safely and have understood the result-
ing risks. aged 3 to 8 years are only allowed to
operate the tap connected to the appliance. Chil-
dren must never play with the appliance. Children
must never clean the appliance or perform user
maintenance unless they are supervised.
- The connection to the power supply is only per-
missible as a permanent connection in conjunc-
tion with the removable cable grommet. Ensure
the appliance can be separated from the power
supply by an isolator that disconnects all poles
with at least 3mm contact separation.
- Secure the appliance as described in chapters
"Installation/ Preparations" and "Installation/ In-
stallation/ Appliance installation".
- Observe the minimum and maximum water inlet
pressure (see chapter "Installation/Specification/
Data table").
- Drain the appliance as described in the chap-
ter "Installation/ Maintenance/ Draining the
appliance".
- Install a residual current device (RCD).
Sealed unvented operating mode:
- The appliance is under pressure. During the heat-
up process, expansion water will drip from the
safety valve.
- Regularly activate the safety valve to prevent
it from becoming blocked, e.g. by limescale
deposits.
- Install a type-tested safety valve in the cold water
supply line. Please note that, depending on the
static pressure, you may also need a pressure re-
ducing valve.
- Size the drain so that water can drain off unim-
peded when the safety valve is fully opened.
- Fit the discharge pipe of the safety valve with
a constant downward slope and in a room free
from the risk of frost.