STIEBEL ELTRON WPL 09 ICS classic - Page 32

INSTALLATION
Specication
32 |WPL ICS classic | WPL IKCS classic www.stiebel-eltron.com
AA01 WPM heat pump manager
AA02 Integral heat pump control unit 1 IWS3 MOD.LC
AA04 Inverter
AA06 Programming unit
AA07 PCB, booster heater MFG
BF01 Heating circuit flow rate sensor
BL01 Condensate float switch
BP01 Pressure sensor, high pressure (42 bar)
BP03 Pressure sensor, low pressure (16 bar)
BP05 Pressure switch, high pressure (45 bar)
BP10 Pressure sensor, heating circuit
BP11 Air differential pressure sensor
BT01 Temperature sensor, heat pump flow
BT02 Temperature sensor, heat pump return
BT03 Heat pump flow temperature sensor downstream of
booster heater
BT30 Outside temperature sensor
BT40 Temperature sensor, hot gas
BT42 Temperature sensor, condenser (frost protection)
BT44 Temperature sensor, evaporator inlet
BT45 Evaporator discharge temperature sensor
BT46 Compressor intake temperature sensor
BT48 Oil sump temperature sensor
BT51 Compressor temperature controller
BT55 Temperature limiter, high limit safety cut-out, MFG
EB03 Oil sump heater
FC07 Condensate pump fuse 10A
KF20 Relay, booster heater MFG
KF21 Relay, booster heater MFG
KF22 Relay, booster heater MFG
MA01 Compressor motor
MA04 Expansion valve motor
MA07 Motor, diverter valve, defrost
MA10 Motor, heat pump heating circuit
MA13 Condensate pump motor
MA15 Motor, diverter valve, heating/DHW
MA16 Motor, valve, inverter cooling
MA20 Motor, heat pump fan
RF02 Radio interference suppression capacitor
RF05 Split ferrite ring core D=6-7.5
RF06 Ferrite ring core D=27mm
RF07 Ferrite ring core D=27mm
RF08 Split ferrite ring core D=10-12
XD01 Terminal, heat pump power supply
XD02 Terminal, MFG/NHZ power supply
XD03 Terminal, control unit power supply
XD20 Terminal, power supply connection, internal
XE15 Earth terminal, control panel
XE16 Earth terminal, inverter, internal
XE18 Earth terminal WPM
XE05 Earth stud, front panel
XE14 Earth stud, WPM
X1.1 WPM CAN connection for heat pump
X1.2 CAN connection for programming unit
X1.3 WPM outside temperature sensor
X1.4 WPM buffer sensor (heating circuit sensor 1)
X1.6 WPM heating circuit sensor 2
X1.8 WPM DHW cylinder sensor
X1.10 WPM heat source 2 (HS2)
X1.11 WPM flow, cooling
X1.12 WPM DHW circulation sensor
X1.14 WPM analogue input 0-10V
X1.15 WPM analogue input 0-10V
X1.16 WPM PWM output 1
X1.17 WPM PWM output 2
X1.19 WPM CAN MFG
X2.1 WPM power supply
X2.2 WPM L’ (power supply utility input), L* (pumps L)
X2.3 WPM heating circuit pump 1
X2.4 WPM heating circuit pump 2
X2.10 WPM fault output
X2.11 WPM DHW circulation pump / HS2 DHW
X2.14 WPM mixer heating circuit 2
X11.1 3-pin IWS plug - power supply control
X11.3 2-pin IWS plug - defrost valve
X11.4 2-pin IWS plug - oil sump heater
X11.8 3-pin IWS plug – power-OFF, float switch
X12.2 12-pin IWS Rast plug - temperature sensor 1
X12.3 3-pin IWS Rast plug - BUS connection
X12.4 7-pin IWS Rast plug - high/low pressure
X12.5 5-pin IWS Rast plug - expansion valve
X12.6 5-pin IWS Rast plug - inverter cooling valve
X12.7 6-pin IWS Rast plug - temperature sensor 2
X12.9 7-pin IWS Rast plug - air differential pressure sensor
X12.11 4-pin IWS Rast plug - Modbus inverter