How to replace high-limit thermostat defect in Strebel Boiler?
If the high-limit thermostat is defective in your Strebel Boiler, replace it by unscrewing it from the brass nut. Note that no draining is needed, and do not remove the brass nut.
Why is the water pressure too high in my Strebel SC-B?
If the water pressure in your Strebel Boiler's CH system is too high, it may be due to too much water being added. Drain some water and check the pressure in the expansion vessel for the correct air cushion pressure, ensuring you check with zero water pressure. If the expansion vessel is defective, replace it.
What to do if the pump is not running in my Strebel SC-B?
If the pump in your Strebel Boiler is not running, it might be seized. Try to loosen the pump spindle or replace the pump drive.
Why is gas not supplied to my Strebel SC-B?
If gas is not being supplied to your Strebel Boiler, the gas valve may not be open. Open the gas valve to resolve this issue.
What to do if Strebel Boiler fan is defective?
If the fan in your Strebel Boiler is defective, replace it.
How to check incorrect fan plug connection in Strebel Boiler?
If the fan plug is connected incorrectly in your Strebel Boiler, ensure the plug/wire connection points to the outside of the fan and that one side fits into the groove on the PCB.
How to remove moisture in pump wiring of Strebel SC-B?
If there's moisture in the pump wiring of your Strebel Boiler, remove the connection and blow dry it using a hairdryer.
How to remove moisture in fan connection of Strebel SC-B?
If there's moisture in the fan or the fan connection of your Strebel Boiler, remove the connection and blow dry it using a hairdryer.
What to do if Strebel SC-B has gas lines issue?
If the gas pipe diameter is too small in your Strebel Boiler, change the gas lines.
How to fix short-circuit in ignition system of Strebel Boiler?
If there's a short-circuit in the ignition system of your Strebel Boiler, check the cable for a short-circuit, overheating, or if it's jammed. Also, check the spark plug cap for cracks and replace it if necessary.
Diagram and explanation of a single boiler system setup.
Diagram and explanation of a multi-boiler cascade system setup.
Explanation of the high efficiency and condensation principles of S-CB boilers.
Details on boiler control methods like flame modulation and external controls.
How the boiler protects itself from frost damage.
Explanation of integrated cascade control for multiple boilers.
Instructions for unpacking the boiler and its included components.
Guidelines for choosing an installation location and area provisions.
Instructions for physically mounting the boiler.
Information on different air supply and flue configurations.
Details on the air inlet and flue gas outlet systems.
Table of resistance values for flue and air inlet systems.
Tables detailing resistance for single and cascade air inlet systems.
Tables detailing resistance for single and cascade flue systems.
Worked examples for calculating flue resistance.
Example calculation for selecting flue diameter based on resistance.
Instructions for connecting and maintaining the condensate drain.
Information on the central heating circuit and bypass requirements.
Guidance on selecting and fitting the expansion vessel.
Details on the internal pump's operation and settings.
Requirements and sizing for low loss headers in cascade layouts.
Procedures for connecting the boiler to the main power supply.
Details on boiler plugs, connector strips, and wiring terminals.
Information on whether the boiler is sensitive to phase or polarity.
Details on the fuses used in the boiler and their ratings.
Example wiring diagram for a cascade boiler installation.
Description of the boiler's control panel elements and their functions.
Explanation of steady display codes indicating boiler status.
Explanation of flashing codes indicating lock-out conditions.
Uses of buttons and knobs on the display console.
Procedures for filling and venting the boiler and heating system.
General steps for commissioning the boiler.
Procedure for setting the boiler's maximum output.
Procedure for setting the boiler's minimum output.
Procedures for converting the boiler from natural gas to LPG.
Table of lock-out codes and their possible causes.
List of common complaints not indicated by display codes.
General guidelines for boiler inspection frequency and conditions.
Specific checks to be performed during a major service.
Reasons and actions for performing maintenance based on inspection.
Guidance on instructing the user on safe operation and maintenance.
To Next Page
General
