Strong SRT 24HY4003 User Manual (English)

Questions and Answers:

J
Jessica HollowayAug 18, 2025
How to improve snowy dots, blocking and interference on Strong SRT 24HY4003?
- A
  Alexandria HardyAug 18, 2025
  If you're seeing snowy dots, blocking, or interference on your Strong LED TV, especially if the antenna is in a fringe area with a weak signal, try these steps: 1. Install a special antenna to improve reception. 2. Adjust the position and orientation of the indoor/outdoor antenna. 3. Check the antenna connection. 4. Fine-tune the channel. 5. Try another channel.
R
Ronald SerranoAug 20, 2025
How to remove unordered ripples on the picture of Strong SRT 24HY4003 LED TV?
- T
  Tristan PriceAug 20, 2025
  Unorderly ripples on the picture are usually caused by local interference from sources like cars, daylight lamps, and hair dryers. Adjust the antenna to minimize the interference.
Z
zacharywoodAug 23, 2025
How to fix ghosting on Strong SRT 24HY4003?
- L
  Luke DicksonAug 23, 2025
  Ghosting occurs when the television signal follows two paths. Changing the direction or position of the antenna may improve reception.
H
Haley SandersAug 26, 2025
What to do if my Strong LED TV has no picture and no sound?
- J
  Jessica FoxAug 26, 2025
  If your Strong LED TV shows no picture and produces no sound, try the following: 1. Check if the fuse or circuit breaker is working. 2. Plug another electrical device into the outlet to ensure it is working or turned on. 3. Ensure the power plug is making good contact with the outlet. 4. Check the signal source.
J
Jennifer WalkerAug 28, 2025
How to fix a Strong SRT 24HY4003 remote control that is not working?
- B
  brenda65Aug 28, 2025
  If the remote control for your Strong LED TV isn't working, try these steps: 1. Replace the batteries. 2. Make sure the batteries are installed correctly. 3. Ensure the main power is connected.
C
Christopher AdamsAug 30, 2025
Why is there normal picture but no sound on my Strong SRT 24HY4003 LED TV?
- M
  Mark DunnAug 31, 2025
  If your Strong LED TV has a normal picture but no sound, consider these solutions: 1. Press the volume up button to increase the volume. 2. Check if the volume is set to mute; if so, press the mute button to restore the sound. 3. Try changing the sound system. 4. Broadcasting failure may be the reason.
D
Deborah CallahanSep 2, 2025
What to do if my Strong SRT 24HY4003 LED TV has no picture but normal sound?
- K
  Kathy KennedySep 2, 2025
  If your Strong LED TV has no picture but normal sound, try adjusting the brightness and contrast. A broadcasting failure may also be the cause.
W
Wendy MaldonadoSep 5, 2025
How to fix no signal or weak signal on Strong SRT 24HY4003?
- A
  Andrew AllenSep 5, 2025
  If you are experiencing no signal, a weak signal, or intermittent reception on your Strong LED TV, consider the following: * Check the cable connections, LNB, and other equipment connected between the LNB and the receiver, or peak the dish. Wait for rain/storm to subside. * The satellite dish may not be pointing at the correct satellite. Adjust the dish. * The satellite dish might be too small, or there might be trees or buildings in the path. Change to a larger dish or change the position of the dish. * The signal may be too strong, indicating the dish is oversized. Connect a signal attenuator to the LNB input.
V
Victoria RamirezSep 7, 2025
Why does my Strong SRT 24HY4003 LED TV have bad picture or blocking error during heavy rain?
- S
  Sheri ChapmanSep 7, 2025
  Heavy rain can weaken satellite signals, leading to blocking. Ensure your dish installation is up to standard to minimize the effects of rain.
J
Justin MartinSep 10, 2025
How to fix no color on Strong SRT 24HY4003?
- M
  Mitchell MillerSep 10, 2025
  If your Strong LED TV has no color, try the following: 1. Change the color system. 2. Adjust the saturation. 3. Try another channel.