What should I do if my Sullair Air Compressor displays a pressure sensor error?
Tighten the pressure sensor wire and reset the air compressor. If the error re-occurs, contact the local Sullair distributor to replace the pressure sensor.
How to reduce excessive noise from my Sullair SRL-7.5MB Air Compressor?
Excessive noise may be due to several factors. Ensure the air compressor is installed on level ground according to the installation procedure. Check if transport fixtures were not removed and remove them. Also, re-tighten or replace the V-belt if it is loose. If the rubber vibration isolators are worn, they should be replaced. For issues related to the SRL reverse rotation, scroll head failure, or electric motor failure, contact your local Sullair distributor.
What to do if my Sullair Air Compressor has low discharge pressure?
Low discharge pressure can be caused by a few things. First, check for leaks in the internal air compressor piping and re-tighten all the air compressor pipe fittings. If the safety relief valve is leaking, replace it. A clogged or dirty intake air filter can also cause this issue, so replace the intake air filter element. For check valve failure, contact the local Sullair distributor.
What causes high discharge pressure in my Sullair Air Compressor?
High discharge pressure can be caused by a printed circuit board failure or electromagnetic contactor failure. Contact the local Sullair distributor to replace these components.
Why is the electric motor overheating in my Sullair Air Compressor?
Overheating of the electric motor may be due to a failed motor bearing, a worn seal, or a short-circuited motor. Contact the local Sullair distributor to replace the electric motor.
How do I fix a phase reversal error on my Sullair SRL-7.5MB Air Compressor?
To fix a phase reversal error, change two of the three incoming power cables.
How to troubleshoot an ambient temperature sensor error on a Sullair SRL-7.5MB?
Check the temperature sensors and the wiring to verify that they are not broken and the connectors are not disconnected. Reset the air compressor, and if the error re-occurs, contact the local Sullair distributor.
What does the maintenance alarm mean on my Sullair Air Compressor?
This alarm is displayed when the total operating hours exceed 2,500 hours. Carry out inspection and maintenance of the air compressor.
What does the scroll head maintenance alarm indicate on my Sullair SRL-7.5MB?
This alarm shows when the total operating hours exceed 9,500 hours (145PSIG Model : 4,500 hours). Perform an inspection and maintenance of the scroll head.
What triggers the overhaul alarm on my Sullair SRL-7.5MB?
This alarm appears when the total operating hours exceed between 19,000 to 19,500 hours (145PSIG Model : between 13,500 to 14,500 hours). Carry out overhaul of the Scroll Head.
Safety measures related to operating the air compressor.
Safety measures for performing maintenance and inspection.
Verifying the correct model and included items.
Procedures for moving the air compressor safely.
Guidelines for placing and setting up the air compressor.
Connecting the air compressor to the air receiver system.
Connecting the main power supply and internal wiring.
Details on terminal block connections for remote control.
Explanation of the control panel indicators and switches.
Steps and settings before starting the air compressor.
Procedure to adjust maximum and recovery pressure settings.
Step-by-step guide for starting the air compressor.
Procedures for starting and stopping the compressor daily.
Daily tasks for maintaining the air compressor.
Checking and tightening fasteners for safety and function.
Procedure for inspecting and replacing the intake air filter.
Verifying the proper operation of the cooling fans.
Maintenance tasks required at 500-hour or 2-month intervals.
Inspecting the check valve for leaks or reverse rotation.
Checking V-belts for noise, slippage, or damage.
Replacing the intake air filter periodically.
Key maintenance tasks at 10,000-hour or 4-year intervals.
Replacing the rubber hose at specified intervals.
Checking the check valve for wear and potential malfunction.
Key maintenance tasks at 20,000-hour or 8-year intervals.
Understanding error codes and alarm messages displayed on the unit.
Details on optional error and alarm indications.
Diagram showing dimensions and component locations for SRL-7.5MB.
Diagram showing dimensions and component locations for SRL-11MB.
Diagram showing dimensions and component locations for SRL-16.5MB.
General| Brand | Sullair |
|---|---|
| Model | SRL-7.5MB |
| Category | Air Compressor |
| Language | English |
To Next Page