Sulzer ABS XFP-PE4 Workshop Manual

68 pages

To Next Page

Workshop Manual

www.sulzer.com

05/2021

Submersible Sewage Pump Type ABS XFP-PE4 [NG2]

Submersible Mixed Flow Column Pump Type ABS AFLX-PE4 [NG2]

Submersible Propeller Pump Type ABS VUPX-PE4 [NG2]

Default Chapter2
- Table of Contents2
Health and Safety Instructions4
General4
- Dimensions and Weights4
- Tightening Torques5
- Equipment and Tools5
Explosion Approved Motor6
- General6
- Workshop Repair6
- Guidelines for Repair6
- Flame Paths6
- Dimensional Checks Drawing for Explosion Approved Motors PE47
Motor Unit XFP - PE4 with Cooling Jacket8
Motor Unit XFP - PE4 Without Cooling Jacket10
Motor Unit VUPX - PE412
Motor Unit AFLX 0600 - PE414
Motor Unit AFLX 0700 - PE416
Hydraulics XFP - PE418
- CB Impeller18
- Impeller20
Hydraulics VUPX - PE423
- Hydraulic23
- Diffuser24
Hydraulics AFLX - PE425
- Hydraulic25
- Diffuser26
Mechanical Seals - Removal and Fitting27
- Primary Seal - Hydraulic Side (Cooled and Non-Cooled Versions)27
- Secondary Seal and Lipseal - Motor Side (Cooled and Non-Cooled Versions)28
Bearings - Removal and Fitting30
Cooling Jacket - Removal and Fitting34
Stator - Removal and Fitting36
Oil and Coolant Changing38
Cable - Removal and Fitting41
- Standard and ATEX Cable Inlet41
- US Cable Inlet42
Test Procedures43
Tool Drawings44
- Wear Ring Removal Tool44
- Mechanical Seal Press Tool - Primary Static Seal45
- Mechanical Seal Press Tool - Primary Dynamic Seal46
- Shaft Sleeve too - Secondary Seals47
- Lipseal Press Tool48
- Press Tool - Compression Fitting49
- Mechanical Seal Press Tool - Secondary Static Seal50
- Mechanical Seal Press Tool - Secondary Dynamic Seal51
- Air Pressure Test Piece52
- Upper Bearing Press Tool53
- Bearing Alignment Sleeve54
- Bottom Bearings Press Tool55
- Upper Bearing Lid Alignment Tool56
- Stator Press Tool57
- Pressure Test Tool58
- Stator Extraction Tool59
- Stator Puller Disc Tool60
- 15.18 Cooling Jacket Fitting Tool61
Terminal Block Wiring62
- 230/3/50 Yδ, 400/3/50 Yδ, 500/3/50 Yδ, 460/3/60 Dol, 600/3/60 Dol62
- 380/3/60 Yδ, 220/3/60 Yδ, 208/3/60 Dol, 220/3/60 Dol, 230/3/60 Dol63

Other manuals for Sulzer ABS XFP-PE4

Installation And Operating Instructions36 pages

Need help?

Do you have a question about the Sulzer ABS XFP-PE4 and is the answer not in the manual?

Sulzer ABS XFP-PE4 Specifications

General

Type	Submersible Sewage Pump
Maximum submersion depth	20 m
Material	Cast iron
Outlet size	80 mm
Liquid temperature	0°C to 40°C
Application	Wastewater, sewage
Operating Temperature	0°C to 40°C

Related product manuals

Sulzer ABS Piranha S10/4-60

20 pages

Sulzer ABS XFP-PE4 Workshop Manual

Table of Contents

Other manuals for Sulzer ABS XFP-PE4

Sulzer ABS XFP-PE4 Specifications

Related product manuals